A synchronous state machine has two inputs (X1 and X2) and two outputs (Z1 and Z2). The inputs represent a 2-bit binary number (N). If the present value of (N) plus the previous value of (N) is greater than (2), then (Z1=1). If the present value of (N) times the previous value of (N) is greater than (2), then (Z2=1). Otherwise, (Z1Z2=00). When the first pair of inputs is received, use (0) as the previous value of (N). The minimal Mealy state diagram of the aforementioned state machine * includes . . states

A synchronous state machine has two inputs (X1 and X2) and two outputs (Z1 and Z2). The inputs represent a 2-bit binary number (N). If the present value of (N) plus the previous value of (N) is greater than (2), then (Z1=1). If the present value of (N) times the previous value of (N) is greater than (2), then (Z2=1). Otherwise, (Z1Z2=00). When the first pair of inputs is received, use (0) as the previous value of (N). The minimal Mealy state diagram of the aforementioned state machine * includes . . states

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.6P

See similar textbooks

Similar questions

Calculating the separation and / or joining angles in the negative feedback control circuit, if any, given as Controlling (K) and Controlled G (s) = (s + 1) / (s2-4 * s + 5) Explanation: The roots of the equation (s2-4 * s + 5); s1 = 2 + 1 * j and s2 = 2-1 * j and the system Transfer Function is TF (s) = K * G (s) / (1 + K * G (s)). a. There are split angles up to (+108.435) and (-108.435) b. There are split angles as much as (+71,565) and (-71,565) c. There are conjunction angles of (+90) and (-90). D. There are separation angles as much as (+18.435) and (-18.435). E. There are no separation and convergence angles.
1. Give an example of open loop and closed loop system (one example each). Also state the input, control system, feedback and output parameter. Example. 1. Open Loop - Water Heater: Input - Water Temperature (Cold) System - Heating Element Output - Water Temperature (Hot) 2. Closed Loop - Air-conditioning System Input - Desired Room Temperature Control - Motor controller/Compressor/ACU Feedback - Temperature Sensing Output - Room Temperature
Figure 1 shows an electrical system comprising a series RLC circuit and input voltagesource ein(t).(a) Derive the input-output equation with output y = I and input u = ein(t). (b) Using the derived input-output equation, drive the system transfer function G(s)that relates output to input. Use the following numerical values for the electrical systemparameters: resistance R = 2Ω, inductance L = 0.25H, and capacitance C = 0.4F. (c) Using the derived transfer function, derive the time-domain ordinary differentialequation for the input-output equation of this electrical system. (d) Draw the complete block diagram of this series RLC circuit using the derived transferfunction.
A stock-flow system models the level of water in a lake. Near a certain equilibrium point, there are three feedback loops: an amplifying feedback loop with strength of +0.55 per month, a stabilizing feedback loop with strength of -0.09 per month, and an amplifying feedback loop with strength of +0.79 per month. Calculate the strength of the overall feedback.
Sketch the level response for a bathtub with cross-sectional area of 8 ft 2 as a function of time for the following sequence of events; assume an initial level of 0.5 ft with the drain open. The inflow and outflow are initially equal to2ft3/min.(a)The drain is suddenly closed, and the inflow remains con-stant for 3 min (0≤t≤3).(b)The drain is opened for 15 min; assume a time constant in a linear transfer function of 3 min, so a steady state is essentially reached (3≤t≤18) (c)The inflow rate is doubled for 6 min (18≤t≤24).(d)The inflow rate is returned to its original value for 16 min(24≤t≤40).
TIME DOMAIN MODELING AND RESPONSE FOR CONTROL SYSTEMS
PLEASE GIVE COMPLETE AND DETAILED SOLUTION The oven shown in Figure 1 has a heating element, qi with capacitances C = 50 J/K. The corresponding temperature is T and ambient temperature is Ta. The thermal resistance of the oven wall is R = 2 K-s/J. The system has a steady-state error in the response, T(t) to a change in the reference input. The steady state error can be reduced if a proportional control action, Kp is included in the controller. Determine the range of values of Kp of the system so that the steady state error is lower than 0.4. (Hint: Kindly determine the steady state error at value 0.4)
Example 1.1 Figure 1.5 shows the block diagram of a closed-loop flow control system. Identify the following elements: (a) the sensor, (b) the transducer, (c) the actuator, (d) the transmitter, (e) the controller, (f) the manipulated variable, and (g) the measured variable. In the figure above, the (a) sensor is labeled as the pressure cell. The (b) transducer is labeled as the converter. However, there are two converters: one for converting pressure to current, and another converting current to pressure for operating the actuator. The (c) actuator is labeled as the pneumatic valve. The (d) transmitter is labeled as the line driver. The (e) controller is labeled as the PLC. The (f) manipulated variable is labeled as the pressure developed by the fluid flowing through the orifice plate. The (g) measured variable is the flow rate of the liquid.
a)If the system has a transfer function of the form G_P (s)=H(s)/(V_m (s) )=μ/(1+Ts) where µ is the gain and T is the time constant, calculate values for µ and T for the case where the valve is at position 3. Hints: Use the constants and information in table 1. The dynamics of the water tank can be found by applying the continuity equation: qin - qout = rate of change in water tank
root locus electrical engineering Don't overthink and reject. Complete the solution as per the given transfer function. No need of quadratic equation just simplify for the exact given transfer function.
Do not do the matlab part
1.Design a sequential circuit with two D Flip-Flops, A and B, and one input x. When x = 0, then the state of thecircuit remains the same. When x =1, the circuit goes through the state transitions from 00 to 01 to 11 to 10back to 00, and repeats.