A thin rectangular plate of dimensions 100 mm x 250 mm is formed by welding two triangular plates. The plate is subjected to a compressive stress of 2.5 MPa in longitudinal direction and a tensile stress of 12 .0 MPa in the transverse direction. Determine the normal stress ow acting perpendicular to the line of the weld and the shear stress Tw acting parallel to the weld. 12.0 MPa Weld -250 mm- 100 mm 2.5 MPa

A thin rectangular plate of dimensions 100 mm x 250 mm is formed by welding two triangular plates. The plate is subjected to a compressive stress of 2.5 MPa in longitudinal direction and a tensile stress of 12 .0 MPa in the transverse direction. Determine the normal stress ow acting perpendicular to the line of the weld and the shear stress Tw acting parallel to the weld. 12.0 MPa Weld -250 mm- 100 mm 2.5 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN
For the two-dimensional stress fi eld shown in Fig. it isfound thatσxx = 3000 lbf/ft2 σyy = 2000 lbf/ft2σxy = 500 lbf/ft2Find the shear and normal stresses (in lbf/ft 2 ) acting onplane AA cutting through the element at a 30° angle asshown.
A thin-walled pressure vessel is made of steel with a thickness of 2 mm and an internal diameterof 300 mm. It is subjected to an internal pressure of 10 MPa. Determine the hoop stress andlongitudinal stress developed in the vessel.
A 14 mm diameter rivet joins the plates that are each 1.10 m wide. The allowable stresses are 120 000 KPa for bearing in the plate material and 60 000 KPa for shearing rivet. Determine the minimum thickness of each plate and the largest average tensile stress in the plates
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar. Express your answer in MPa.
The pressure tank shown is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown where β=55∘β=55∘. The tank has an inside diameter of 26.626.6 in.in. and a wall thickness of 0.3500.350 in.in. Determine the largest gage pressure that can be used inside the tank if the allowable normal stress perpendicular to the weld is 18.518.5 ksiksi and the allowable shear stress parallel to the weld is 8.58.5 ksiksi.
The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and 55 MN/m2 tension respectively. The shear stress across these planes is 25 MN/m2 (Counter clockwise). Determine the magnitude of the normal, tangential, the resultant stress, and inclination of resultant stress on a plane inclined at 25o to the plane of greater principal stress. And also verify the answer by drawing the Mohr’s circle.
A cylinder having an internal diameter of 22 in. and an external diameter of 38 in. is subjected to an internal pressure of 12,000 psi and an external pressure of 2300 psi. Determine the hoop stress at the inner and outer surface of the cylinder. d.14,789 psi and 6,879 psi c.13, 143 psi and 5,143 psi b.15,876 psi and 8,366 psi a.17,181 psi and 7,481 psi
A cylinder having an internal diameter of 16 inches and external diameter of 26 inches is subjected to 1,500 psi external pressure and internal pressure of 9,000 psi. Determine the hoop stress on the outer surface of the cylinder. A. 7,642.84 psi C. 5,284.67 psi B. 6,466.24 psi D. 8,833.02 psi
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.