2. A cylindrical pressure vessel is made of thin steel plate of thickness t = 1Omm and it has an inner diameter of 600 mm. Steel plates are welded in a helical fashion with an angle 0 as shown. If the cylinder is to support a gage pressure of 5 MPa and the maximum shear strength of the weld joint along the weld is 30 MPa, determine the helical angle at which the welding must be done. P= 5 MPa t= 10 mn weid joint Y = 300 wA ul

2. A cylindrical pressure vessel is made of thin steel plate of thickness t = 1Omm and it has an inner diameter of 600 mm. Steel plates are welded in a helical fashion with an angle 0 as shown. If the cylinder is to support a gage pressure of 5 MPa and the maximum shear strength of the weld joint along the weld is 30 MPa, determine the helical angle at which the welding must be done. P= 5 MPa t= 10 mn weid joint Y = 300 wA ul

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown below. The pressure in the tank is 2.76 MPa, and an axial load of 133.5 KN is applied to the end of the tank through a rigid bearing plate. Determine the normal stress and shearing stress perpendicular to the weld.
A rectangular steel plate is welded as a cantilever to a vertical column and supports a single concentrated load P. Determine the weld size if shear stress in the same is not to exceed 140 MPa
A circular steel bar 50 mm diameter and 200 mm long is welded perpendicularly to a steel plate to form a cantilever to be loaded with 5 kN at the free end. Determine the size of the weld, assuming the allowable stress in the weld as 100MPa.
A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in shear on the weld is 15,800 psi, the minimum effective length of the weld must be A. 5.4 B 4.9 in C. 4.3 in D 3.9 in.
The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld cannot exceed 3 in. If the weld must transmit a total force equal to 9600 lb, it’s size should be A. 1/2 in. B. 3/8 in. C. 5/16 in. D. 1/4 in.
A tension plate shown below is used to support suspended load "T". Gusset Plate F, = 248 MPa Fu = 400 MPa 200 mm. Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory)
A welded connection has an effective length of 150 mm. 12 mm fillet welds are used. If the ultimate strength of the weld is 485 MPa and its allowable shearing stress is 60% of Fuw. Determine the allowable shearing stress of the weld in MPa.
appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in).
Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN
Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN Please send the solution within half an hour and thank you
The two steel members are joined together using a 30∘∘ scarf weld. Forces of F=12.5 kNF=12.5 kN are applied at each end, as shown. (Figure 1) PART A) Determine the average normal stress resisted in the plane of the weld. Express your answer to three significant figures and include appropriate units. PART B) Determine the average shear stress resisted in the plane of the weld. Express your answer to three significant figures and include appropriate units.
A double riveted butt joint, in which the pitch of the rivets in the outer rows is twice that in the inner Rows, connects two 16mm thick plates with two cover plates each 12 mm thick. The diameter of rivets is 22 mm. Determine the pitches of the rivets in the two rows if the working stresses are not to exceed the following limits: Tensile stress in plates =100 MPa; Shear stress in rivets =75 MPa; and bearing stress in rivets and plates =150 MPa. Make a fully dimensioned sketch of the joint by showing at least two views.