as is subjected to a static eccentric force of F=25 kN in the plane of the welds. The allowable shear stress for the weld is 37.5 dia. 75 Tal = 90 MPa, determine the leg size h of the welds if two parallel horizontal fillet welds are used. 1018 HR 1018 HR Knowing: l4 = 350mm; l2 = 200mm For two parallel fillet welds: d(3b²+d²). 'F Fig. 1 Ju 0.707hJu, where dis the weld length of the weld, b is the distance between two welds. %3D %3|

as is subjected to a static eccentric force of F=25 kN in the plane of the welds. The allowable shear stress for the weld is 37.5 dia. 75 Tal = 90 MPa, determine the leg size h of the welds if two parallel horizontal fillet welds are used. 1018 HR 1018 HR Knowing: l4 = 350mm; l2 = 200mm For two parallel fillet welds: d(3b²+d²). 'F Fig. 1 Ju 0.707hJu, where dis the weld length of the weld, b is the distance between two welds. %3D %3|

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4) A welded connection, as shown in Fig. 2, is subjected to an eccentric force of 60 kN in the plane of the welds. Determine the size of the welds, if the permissible shear stress for the weld is 200 N/mm2. 60 kN 100 W2 -150 50 Fig. 2 Assume static conditions. 10.09 mm 20.09 mm 30.09 mm 40.09 mm
8) A plate 75 mm wide and 10 mm thick is joined with another steel plate by means of single transverse and double parallel fillet welds as shown in Fig.3. The joint is subjected to a maximum tensile force of 55 kN. The permissible tensile and shear stresses in the weld material are 70 and 50 N/mm2 respectively. The length of each parallel fillet weld is: 55 kN 55 kN Fig.3 O 25.29 mm 40.58 mm O 64.77 mm O97.58 mm 75 mm
Solve Q7 only 4) A welded connection, as shown in Fig. 2, is subjected to an eccentric force of 60 kN in the plane of the welds. Determine the size of the welds, if the permissible shear stress for the weld is 200 N/mm2. 60 kN W3 100 W2 -150 50 Fig. 2 7) What is the value of polar moment of inertia of all welds about C.0.G? 3890094.64 mm4 4528724.56 mm4 6782459.89 mm4 9875612.79 mm4
10. Two tie bars are connected together by 0.5cm fillet welds around the end of 1 bar and the inside of a slot machined in the same bar. Estimate the strength of the connection in tension if the shearing stress in the welds is limited to 75MPa. 450m 10cm 8cm
A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in shear on the weld is 15,800 psi, the minimum effective length of the weld must be A. 5.4 B 4.9 in C. 4.3 in D 3.9 in.
1. A butt weld is set on the cross section of an I-shaped beam. There are bending moment M and shear force V at the splicing position, where M=1120 kN•m and V= 374 kN. The beam is made of Q355b steel and semi-automatic weld is used with welding rod E50. The design value of the weld tensile strength f," is 260 N/mm². Please check whether the strength of the butt weld is safe by calculation. 280 M M 0001
Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN Please send the solution within half an hour and thank you
Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a double parallel fillet weld as shown in Fig. if the permissible tensile and shear stresses in the weld material are otw MPa and tw MPa respectively and the permissible tensile stress in the plate material are otp MPa, Find the length Li of single transverse fillet weld, if the joint is subjected to both static and fatigue loading. All dimensions in mm.
6 in . T F = 2,000 lbs 2-in dia. Given loads: For the specified loading case: • Calculate the force per inch of weld for each of the stress components: the vertical shear, the bending, and the torsion. Determine the combined resultant force per inch of weld. For the specified weld size, calculate the maximum combined shear stress in the weld throat. Answer: Tmax=25.6 psi T = 15,000 in-lbs | • Using the maximum allowable shear stress for A36 steel and a weld electrode of E70 (see Table in your textbook), calculate a new weld size for the same load conditions.
Question: a) A plate 100 mm wide and 10 mm thick is to be welded to another plate by means of double parallel fillets. The plates are subjected to a static load of 80 kN. Find the length of weld if the permissible shear stress in the weld does not exceed 55MPa. Determine the increase in load carrying capacity if a combination of single transverse double parallel fillet is used the permissible tensile strength of material is 80MPa. b) Draw a neat sketch of double riveted double cover but joint. If 8mm plates with 20 mm diameter rivets having a pitch of 50 mm are joint using double riveted lap joint. The permissible stresses are permissible tensile stress = 120 MPa;Permissible crushing stress= 100 MPa; Permissble shear stess= 150 MPa. Find the strengths and efficiency of joint, taking the strength of the rivet in double shear acoording to the indian boiler standards.
The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld cannot exceed 3 in. If the weld must transmit a total force equal to 9600 lb, it’s size should be A. 1/2 in. B. 3/8 in. C. 5/16 in. D. 1/4 in.
) find the required fillet welds size if the allowable shoar stress is 9.4 KN/Cm fot the figure below Talls 190m 450 mm A Ans: h=5.64 mm =30 KN 250 *-F=l。ト %3D