A three-phase motor, Y connection, 380-V, 100-kW, 110- kVA, 50 Hz. Calculate the value of capacitor must be conne in parallel with each phase load to enhance power factor to 0.94 lagging? Design a band pass filter of the form in Fig. 5 with a lower cut off frequency of 25.3 kHz and an upper cut off frequency of 25.6 kHz. Determine L, C, and Q. vj(t) L R= 18 ΚΩ Figure 5 + vo(t) -

A three-phase motor, Y connection, 380-V, 100-kW, 110- kVA, 50 Hz. Calculate the value of capacitor must be conne in parallel with each phase load to enhance power factor to 0.94 lagging? Design a band pass filter of the form in Fig. 5 with a lower cut off frequency of 25.3 kHz and an upper cut off frequency of 25.6 kHz. Determine L, C, and Q. vj(t) L R= 18 ΚΩ Figure 5 + vo(t) -

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A circuit comprises of a coil (resistance of 20W, inductance of 400mH), and a capacitor of 2.0mF connected in series. A supply of 100V at 50 Hz is connected across the circuit. (i) Calculate the circuit: Impedance Phase angle Resonant frequency Q-factor Bandwidth (ii) How do each of the parameters in c., d., e., change if the coil is connected in parallel with the capacitor across the same supply? (iii)Explain what is happening to both parallel and series connections of the above circuit at resonant frequency and critically analyse the effects on circuit currents, voltages and components at resonance.
Q1) Find the out voltage as a function of input voltage of the RC filter of Fig.1. Sketch themagnitude and phase. Q2) Sketch the frequency response for the amplifier shown in Fig.2.
Consider a lead network with a lower frequency break of 800 Hz. Calculate the frequency at which the gain will be -24.6 dB?
What is the effect on the signal–to–noise ratio of a system (in dB) if the bandwidth is doubled, considering all other parameters to remain unchanged except the normal thermal noise only? The S/N will be ______. I need answer ASAP. Thank you!
1.) Considering the 2nd order filter given, what values of R1, R2, C1, and C2 will give the narrowest bandwidth? a.) R1= 0.26kOhms, R2 = 6.5kOhms, C1 = C2 = 120nF b.) R1= R2 = 0.75kOhms, C1 = 110nF, C2 = 4.4nF c.)R1= R2 = 0.75kOhms, C1 = C2 = 22nF d.)R1= R2 = 1.3kOhms, C1 = C2 = 120nF 2.) Considering the 2nd order filter given, which among the four choices gives the largest bandwidth? a.)R1 = R2 = 0.75kOhms, C1 = C2 = 22nF b.)R1 = R2 = 0.75kOhms, C1 = 110nF, C2 = 4.4nF c.)R1 = 0.15kOhms, R2 = 3.75kOhms, C1 = 110nF, C2 = 4.4nF d.)R1 = 0.26kOhms, R2 = 6.5kOhms, C1 = C2 =120nF 3.)Considering the 2nd order filter given , which among the four choices gives the slowest settling time? a.)R1 = 0.15kOhms, R2 = 3.75kOhms, C1 = 110nF, C2 = 4.4nF b.)R1 = 0.26kOhms, R2 = 6.5kOhms, C1 = C2 = 120nF c.)R1 = R2 = 0.75kOhms, C1 = 110nF, C2 = 4.4nF d.) R1 = R2 = 1.3kOhms, C1 = C2 = 120nF
4.Q-factor 5.Bandwidth (ii) How do each of the parameters in 3, 4., 5., change if the coil is connected in parallel with the capacitor across the same supply?
An impedance coil having a resistance of 30 ohms and a 50 cps inductive reactance of 33.3 ohmsis connected to a 125 volt 60 cps source. A series circuit consisting of a 20 ohm resistor and avariable capacitor is then connected in parallel with the coil. (a) for what values of capacitancewill the circuit be in resonance? (b) calculate the two values of line current for the condition ofresonance.
A 25 V, 2.5 kHz supply is connected to a network comprising a variable capacitor in parallel with a coil of resistance 250 ohm and inductance 80 mH. Determine for the condi tion when the supply current is a minimum (a) the capacitance of the capacitor, (b) the dynamic resistance, (c) the supply current, (d) the Q-factor, (e) the bandwidth, (f ) the upper and lower half-power frequencies and (g) the value of the circuit impedance at the −3 dB frequencies.
(vsb modulation) 1-Interpret graphs of time domains and explain the relationships between them. 2-Interpret graphs of frequency domains and explain the relationships between them.
Designe two t type matching networks that transforms a ZL=100ohms load to Zin=20-j40ohms input impedance at a nodal quality factor Qin=4 the matching sho uld be achieved at f0=600MHZ
ı just need the fınal answer Since Vcc = 20 V, RS = 3 kΩ, RB = 380 kΩ, RC = 1.2 kΩ, RE = 2.2 kΩ, RL = 911 Ω and β = 90 in the circuit in the figure, find the value of the output voltage (Vo). NOTE-1: It is within the 1 kHz mid-band frequency and the capacitors are negligible at this frequency. NOTE-2: The output impedance (r0) of the transistor will be neglected. a. 64,14 mV b. 83,88 mV c. 93,75 mV d. 74,01 mV e. 103,62 mV f. 24,67 mV g. 34,54 mV h. 49,34 mV
HIGH VOLTAGE(Can you explain in detail? Thank you) Q1 : A 100 kVA, 50 Hz, 230/50 kV testing transformer has an 10% leakage reactance and a 2% winding resistance. A cable of capacitance 100 nF is to be tested at 300 kV using this transformer as part of the resonance circuit. Determine the value of the inductance (with a Q-factor of 20) required to obtain resonance and the value of the input voltage required to obtain the required voltage.