A toaster oven is rated at 1100 W for operation at 120 V, 60 Hz.Part AWhat is the resistance of the oven heater element?Express your answer with the appropriate units.HÅ?R=ValueUnitsSubmitRequest AnswerO Part BWhat is the peak current through it?Express your answer with the appropriate units.μÅ?Io =ValueUnitsSubmit Request Answer

Given data : Rated Power of toaster oven P= 1100W Voltage of toaster oven V=120V

A toaster oven is rated at 1100 W for operation at 120 V, 60 Hz. ▾ Part A What is the resistance of the oven heater element? Express your answer with the appropriate units. μÃ → ? R= Value Units Submit Request Answer Part B What is the peak current through it? Express your answer with the appropriate units. JA ? Io = Value Units

A toaster oven is rated at 1100 W for operation at 120 V, 60 Hz. ▾ Part A What is the resistance of the oven heater element? Express your answer with the appropriate units. μÃ → ? R= Value Units Submit Request Answer Part B What is the peak current through it? Express your answer with the appropriate units. JA ? Io = Value Units

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter4: Conductor Sizes And Types, Wiring Methods, Wire Connections, Voltage Drop, And Neutral Conductor Sizing For Services

Section: Chapter Questions

Problem 35R: A 120-volt branch circuit supplies a resistive heating load of 10 amperes. The distance from the...

See similar textbooks

Similar questions

Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C what is the answer? VD?
equipment grounding 1. The only exception to the need for all information technology equipment to be satisfactorily grounded is where the equipment is A. DC powered.B. backup generator powered. C. double-insulated.D. isolated equipment. 2. Which section of the National Electrical Code lists sizing requirements for wire-type equipment grounding conductors? A. 250.66 B. 250.118 C. 250.4 D. 250.122
4.a. The ___ calculated load is rarely placed on an electrical system.A. optionalB. standardC. total 4.b. What's the primary disadvantage of using copper conductors?A. CostB. AvailabilityC. Weight 4.c. You're evaluating the components of a multioccupancy building that won't have an on-site employee. Tobe compliant with the NEC, each occupant will need to have access to their ownA. service-disconnecting means.B. service conductor.C. cable attachment point.D. emergency fire water-pump disconnect.
Airframe Electrical System Question: By what means should aircraft electrical circuits/wires be protected from excessive current? (Source: FAA AC 43.13-1B/2B)
Airframe Electrical System Question: What is the recommended shield coverage area for wires and cables that are susceptible to EMI? (Source: FAA AC 43.13-1B/2B)
20. A separately derived system is an electrical source, other than a service, having ____ connection(s) to circuit conductors of any other electrical source other than those established by grounding and bonding connections. Select one: A. INDIRECT B. NO DIRECT C. DIRECT D. COMPLETE
Explain each option & Choose the correct option. 4) The _ calculated load is rarely placed on an electrical system.A. optionalB. standardC. total 5) What's the primary disadvantage of using copper conductors?A. CostB. AvailabilityC. Weight 6) You're evaluating the components of a multioccupancy building that won't have an on-site employee. To be compliant with the NEC, each occupant will need to have access to their ownA. service-disconnecting means.B. service conductor.C. cable attachment point.D. emergency fire water pump disconnect ..
Using NEC: What gauge of conductors is required to feed a 240 Volt single-phase air conditioning unit, whose compressor consumes 6000 VA and the condenser motor is 2 amps? Use copper THHN wire connected to 60°C terminals. What is the minimum and maximum allowable ampacity of the air short-circuit protection of the previous example?
Airframe Electrical System Question: What are the two types of wire installation method. (Source: FAA AC 43.13-1B/2B)
If I am running a #12 AWG conductor with a K value of 10.4 for a 120VAC single phase lighting circuit 200 ft, from the junction box inside the building. What voltage would be available at the load and would it meet the NEC recommendation? If not, what would be the solution? If I am running a 3-phase, 120V/208VAC feeder circuit from the first floor service panel to the second floor 200A lighting panel. The distance between is 120 ft. If I use copper wire with a K value of 10.4, what size conductors should I use to meet the recommendations from the NEC for Voltage Drop?
10. Overhead and underground service conductors are governed by the _______ and are the responsibilityof the electrical designer and installer.A. utilityB. NECC. AHJD. property owner
You are a journeyman electrician in an industrial plant. You have been assigned the task of connecting a 25-kW electric heater to a 240-V, single-phase panel. The heater is located in an area with an ambient temperature of 90°F. The conductors are to be copper with Type TW insulation. The heater is expected to operate for more than three hours at a time. What size conductors would you use to connect this heater? Is this correct? I=P/EI=25000 W/ 240 VI= 104.17 amps x 125%I= 130.21 amp/ .96I= 135.63 amp2/0 AWG conductor will be needed