A traffic light weighing 30 pounds is suspended by two wires as shown in the figure below. Find the magnitude |T₁| of the tension in wire AC, and the magnitude /T₂l of the tension in wire AB. (Round your answers to the nearest whole number.) lb lb |T₁|= |T₂| = B T₂ 450! i 60⁰ 000% W T₁

A traffic light weighing 30 pounds is suspended by two wires as shown in the figure below. Find the magnitude |T₁| of the tension in wire AC, and the magnitude /T₂l of the tension in wire AB. (Round your answers to the nearest whole number.) lb lb |T₁|= |T₂| = B T₂ 450! i 60⁰ 000% W T₁

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter26: Electromagnetism

Section: Chapter Questions

Problem 1STP

See similar textbooks

Similar questions

An electric wire having a mass of 0.5 kg/m along the horizontal is suspended between supports of the same elevation which is 50m apart. If the maximum tension in the wire is 800N, find a. the minimum tensionb. the sagc. the length cable ANS.a. 790.17Nb. 1.98mc. 50.2m
The AB cable in the figure is attached to the top of the 3 m high vertical pole and its tension is 50 kN. What are the tensions on the AO, AC and AD cables?
Consider the same situation as in the previous problem. This time the magnet has mass 4.27 kg and the force pulling the magnet to the right has magnitude 83.5 N. What is the magnitude of the tension force in the cord? 153.2 N 222.9 N 93.4 N 125.4 N
Consider the same situation as in the previous problem. This time the magnet has mass 4.12 kg and the force pulling the magnet to the right has magnitude 166.6 N. What is the magnitude of the tension force in the cord? a. 128.2 N b. 171.4 N c. 207.0 N d. 113.5 N
Two cables tied together at C are loaded as shown. The maximum allowable tension in cable AC is 2600 N, and in cable BC is 700 N. Find (a) the magnitude of the largest force P (in N) which may be applied at C and (b) the corresponding angle a (in degrees).
Need some assistance figuring this one out! Force F pulls upward on link A with magnitude 622N , d1 = 3.3m , d2 = 1.7m , d3 = 2.9m , d4 = 4.2m , h = 6.5m 4. What is Express cable AC as a position vector ? (rACx, rACy, rACz) 5. What is the length of cable AC ( |rAC| ) 6. What is cable AC as a unit vector ? ( uACx, uACy, uACz ) 11.What is the tension on cable AC ( TAC)
In the situation below, a conducting loop is pulled at a constant speed through an arrangement of magnets as shown. 1. When entering the space between the magnets, the loop: A. no force to move between the magnets B. experiences force to left pulling it into space between magnets C. experiences force to right is pushed by external force into space of magnets. 2. When leaving the space between the magnets (to the left), the loop: A. no force being experienced B. experiencing a force to the right which leaves it resisting leaving the space between magnets C. experiences force to left leaving and is pushed out of space between magnets.
Which of the following is not a scalar field? a. Temperature distribution in your classroom b. Atmospheric pressure in a given region c. Light intensity in a drawing room d. Displacement of a mosquito in space
QUESTION 2 Consider the same situation as in the previous problem. This time the magnet has mass 6.08 kg and the force pulling the magnet to the right has magnitude 124.7 N. What is the magnitude of the tension force in the cord? A 138.2 N B 184.3 N C 129.0 N D 125.3 N
Same situation as in the previous two problems this time the magnet s mass is 3.54 kg and the magnetic force pulling it to the right is 108.0 N. The length of the cord is 1.13 m, and the ceiling is 2.75 m above the floor. Suppose that you cut the cord and the magnet falls to the floor while still being pulled to the right by the force of 108.0 N. How long will it take the magnet to hit the floor? 0.700 s 0.420 s 0.980 s 0.560 s
Blocks 1 and 2, with masses M1=0.50 kg and M2=1.5 kg, are connected by an ideal string, which passes over a pulley without slipping (see figure). The magnitudes of the wire voltages applied to blocks 1 and 2 are represented, respectively, by T1 and T2. Consider T2>T1. In this case, the pulley rotates counterclockwise. The pulley has radius R=0.46 m and rotates around an axis perpendicular to its surface passing through its CM. The CM of the pulley coincides with its center. The moment of inertia of the pulley with respect to the axis of rotation is denoted by I and the acceleration of the blocks has magnitude 0.025 m/s2. Use g=10 m/s2. Determine I (in kg⋅m2). Choose an option : a) 3,0 b) 4,0 c) 210 d) 41 e) 64 f) 84 g) 8,0 h) 32
A. 0.6873 B. 1.4485 C. 1.4550 D. 1.4559 E. Cannot be determined using the given information