A two-layer wall is made of two metal plates, with surface roughness of about 25 mm, pressed together at an average pressure of 10 MPa. The first layer is a stainless steel plate with a thickness of 5 mm and a thermal conductivity of 14 W/m∙K. The second layer is an aluminum plate with a thickness of 15 mm and a thermal conductivity of 237 W/m∙K. On the stainless steel side of the wall, the surface is subjected to a heat flux of 800 W/m2. On the aluminum side of the wall, the surface experiences convection heat transfer at an ambient temperature of 20°C, where the convection coefficient is 12 W/m2∙K. Determine the surface temperature of the stainless steel plate.

A two-layer wall is made of two metal plates, with surface roughness of about 25 mm, pressed together at an average pressure of 10 MPa. The first layer is a stainless steel plate with a thickness of 5 mm and a thermal conductivity of 14 W/m∙K. The second layer is an aluminum plate with a thickness of 15 mm and a thermal conductivity of 237 W/m∙K. On the stainless steel side of the wall, the surface is subjected to a heat flux of 800 W/m2. On the aluminum side of the wall, the surface experiences convection heat transfer at an ambient temperature of 20°C, where the convection coefficient is 12 W/m2∙K. Determine the surface temperature of the stainless steel plate.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.49P

See similar textbooks

Similar questions

2.34 Show that the temperature distribution in a sphere of radius . made of a homogeneous material in which energy is released at a uniform rate per unit volume , is
1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a well-insulated 40-L tank of water that is initially at 300 K. If each heater dissipates 500 W, what is the time required for bringing the water temperature in the tank to 340 K? State your assumption for your analysis.
A spherical container with an inner radius r1 = 1 m and an outer radius r2 = 1.05 m has its inner surface subjected to a uniform heat flux of q1=7kw/m^2. The outer surface of the container has a temperature T2 = 25°C, and the container wall thermal conductivity is k = 1.5 W/m·K. Show that the variation of temperature in the container wall can be expressed as and determine the temperature of the inner surface of the container at r = r1.
10 hot rods (L = 5 m and d = 2 cm) are buried in the ground parallel to each other each rod is 10 cm apart and at a depth 3 m from the ground surface. The thermal conductivity of the soil is 0.6 W/m K. If the surface temperature of the rods and the ground are 600 K and 30 °C, respectively. Draw the figure and determine the rate of heat transfer from the fuel rods to the atmosphere through the soil
If H is the work output of a heat engine and Q is the total heat input of an engine, then determine its thermal efficiency.
A 75-hp (shaft output) motor that has an efficiency of 91.0 percent is worn out and is replaced by a high-efficiency 75-hp motor that has an efficiency of 95.4 percent. Determine the reduction in the heat gain of the room due to higher efficiency under full-load conditions.
3. A lumped system with a volume of 0.003 m³ and a surface area of 0.08 m² is made of a material with density of 3800 kg/m³, thermal conductivity of 300 W/m K, and specific heat of 200 J/kg K. If the system is exposed to a convection environment with h = 60 W/m2 K, what is the approximate time it will take for this system to reach equilibrium with the environment? Express your answer in minutes.
A mother takes the milk to be given to her baby from the refrigerator and pours it into a cylindrical bottle for heating. The height of the milk in the bottle is 10 cm. Then he places the bottle into a large container with hot water at a temperature of 62 ° C. The heat transfer coefficient between hot water and bottle is 130 W / m2.oC. The process of heating the milk from 4 0C to 40 0C is required to be completed within 6 minutes. What should be the diameter of the bottle used? The properties of milk can be equal to the properties of water at the same temperature.
The resistance of a copper wire used to make a motor is 0.5 Ω at 25C and 0.8 Ω at the motor’s operating temperature. Determine the operating temperature and the rise in temperature of the motor, given that copper has a temperature constant of 234.5C.
Two surfaces of a 2-cm-thick plate are maintained at 0°C and 100°C, respectively. If it is determined that heat is transferred through the plate at a rate of 500 W/m2 , determine its thermal conductivity.
Heat is conducted through a material with a temperature gradient of – 9000 K/m. The conductivity of the material is 25 W/m-K. If this heat is transferred to surroundings at 30°C with a convection coefficient of 345 W/m2 -K, determine the surface temperature, if the heat is radiated to the surroundings at 30°C determine the surface temperature.
A pipe with an outside diameter of 3.5 in. is insulated with a 3 in. layer of asbestos (ka=0.396 BTU-in/hr- ft2 - 0 F), followed by a layer of cork 1.5 in. thick (kc=0.30 BTU-in/hr-ft2 - 0 F). If the temperature of the outer surface of the cork and pipe is 1000 F and 3000 F, respectively, calculate the heat lost per 100ft or insulated pipe.