A vehicle with a direct TPMS just had all 4 tires replaced, yet the TPMS warning light is on. Technician A says this may be due to the tire tech damaging one of the sensors during tire replacement. Technician B says it may be caused by the tire tech damaging the wheel speed sensor during tire install. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or B

A vehicle with a direct TPMS just had all 4 tires replaced, yet the TPMS warning light is on. Technician A says this may be due to the tire tech damaging one of the sensors during tire replacement. Technician B says it may be caused by the tire tech damaging the wheel speed sensor during tire install. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or B

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter51: Drum Brakes

Section: Chapter Questions

Problem 10ASRQ: While discussing pull during braking: Technician A says that this can be caused by one tire being...

See similar textbooks

Similar questions

A vehicle with a direct TPMS system keeps showing “Low-Left Front Tire,” but when checked, the tire is within specification. Which of the following would be the most likely cause? A broken reluctor wheel Multiple TPMS sensors have failed The tires were rotated without doing a re-learn procedure A faulty wheel speed sensor
All tpms have a pressure sensor mounted inside of the tire and wheel assembly
An indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system will typically alert the driver which tire is low. Technician B says that after serving the indirect TPMS, you need to perform a re-learn procedure. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or B
Technician A says that replacement wheel rims should be the same as the original equipment wheels in load capacity, offset, width, diameter, and mounting configuration. Technician B says that if wheels are installed that have a different stock width or diameter, make sure to use a tire that has the same overall width as the original tires. Otherwise the vehicles wheel-speed sensors, speedometer, antiock brake system, and many other systems will be affected. Who is correct? a. Technician A only b. Technician B only c. Both A and B Neither A nor B
While discussing pull during braking: Technician A says that this can be caused by one tire being underinflated. Technician B says that a frozen wheel cylinder on one side of the car can cause this. Who is correct? Technician A only Technician B only Both A and B Neither A nor B
When replacing an air bag module: Technician A says that the steering column clockspring should be maintained in its correct index position at all times. Technician B says that failure to keep the clockspring straight ahead or in the neutral position relative to the steering wheel can cause damage to the enclosure, wiring, or module. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Technician A says that each ABS has its own diagnostic procedure involving use of the brake and antilock warning lamps, special testers, breakout boxes, scan tools, troubleshooting charts, and wiring diagrams. Technician B says that ABSs vary in the number of codes they can store and whether they will retain the code in memory when the ignition is turned off. Who is correct? Technician A only Technician B only Both A and B Neither A nor B
A digital speedometer constantly reads 0 mph: Technician A says that the problem may be the vehicle speed sensor. Technician B says that the problem may be the throttle position sensor. Who is correct? Technician A Technician B Both A and B Neither A nor B
Technician A says that it is normal for the amber brake lamp to light when the ABS is activated during braking. Technician B says that it is normal for the red brake lamp to be on whenever the ignition is on and the engine is off. Who is correct? Technician A only Technician B only Both A and B Neither A nor B
Technician A says that some traction control systems eliminate wheel spin by applying the brakes on the driving wheels. Technician B says that some traction control systems eliminate wheel spin by retarding ignition timing and cutting off fuel injection. Who is correct? Technician A only Technician B only Both A and B Neither A nor B
Which of the following is the most likely cause of a lean condition during acceleration and cruising speeds? a. A defective oxygen sensor b. A defective PCM c. A defective ECT sensor d. A defective MAF sensor
While discussing automatic AWD systems: Technician A says that the systems operate in 2WD nearly all of the time. Technician B says that on many systems, when the PCM receives inputs from the CAN bus, it indicates that wheel slippage power is sent to the other drive axle. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B