When replacing brake pads on a vehicle: Tech-nician A works on one wheel before beginning work on another. Technician B uses a minimum of 52 psi of air pressure to force the piston from the caliper housing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
When replacing brake pads on a vehicle: Tech-nician A works on one wheel before beginning work on another. Technician B uses a minimum of 52 psi of air pressure to force the piston from the caliper housing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Want to see the full answer?
Check out a sample Q&A here
Related Mechanical Engineering Q&A
Q: What is the difference between block brakes with short and long shoes?
A: Block shoe brake : These are mechanical brakes which are operated by mechanical elements ( springs ,…
Q: Which of the following is not done when performing a brake service? A. Measure the rotor for out…
A: During a brake assessment the whole brake framework is checked; this incorporates the following:…
Q: When replacing brake pads on a vehicle: Technician A works on one wheel before beginning work on…
A: Technician A is correct as the brake pad is replaced first. After the first pad is replaced then the…
Q: Which of the following is not likely to cause a pulsating brake pedal? a. Loose wheel bearings b.…
A: When a load or side thrust is applied to the bearings, loose wheel bearings allow the rotor to tip…
Q: Describe the procedure for using compressed air to remove a piston from a brake caliper.
A: Sometimes piston sticks in the bore in a disk brake.
Q: Which of the following is not measured when inspecting the brake rotors and pads?
A: Option (1) is correct. Out of round
Q: Technician A says that an out-of-round drum can cause a pulsating brake pedal. Technician B says…
A: Technician A says that an out-of-round drum can cause a pulsating brake pedal. Technician B says…
Q: have to design a pivoted block brake with shoe
A: Given: A pivoted block brake with shoe To Write: Steps while designing a pivoted block brake with…
Q: Which of the following statements about drum brake shoes is not true? a. Linings may be riveted or…
A: Which of the following statements about drum brake shoes is not true? Given Statements are :-…
Q: While discussing how to remove the piston from a brake caliper: Technician A says that the dust boot…
A: In IC engine maintenance Brake assembly is the critical component Its efficiency directly depends on…
Q: Technician A says that on most vehicles, the wheel/tire assembly is considered sprung weight .…
A: technician A is wrong and technician B is saying correctly.
Q: it has been determined that chatter and brake pull are being caused by hard spots on the brake drum:…
A: The raised or projected surfaces of the brake drum due to braking heat is known as hard spots.
Q: Technician A says that carbon ceramic rotors can sometimes be machined. Technician B says that drums…
A: Yes carbon ceramic material can be machined with tungsten carbide tool. Generally Drum brakes are…
Q: While discussing how to remove the piston from a brake caliper: Technician A says that the dust boot…
A: Technician B says that air pressure should be injected into the bleeder screw’s bore to force the…
Q: why is brake fluid removed from the master cylinder prior to working on disc brakes
A: A disc brake has a master cylinder that contains brake fluid in it. The braking force is first…
Q: which of the following is not measured when inspecting the brake rotors and pads? A. Out of…
A: which of the following is not measured when inspecting the brake rotors and pads?
Q: All calipers have at least one piston that pushes the brake pad against the rotor?
A: The given statement that each caliper requires one piston for pushing the brake pad against the…
Q: Why is brake fluid removed from the master cylinder prior to working on disc brakes?
A: About the (2/3) two-thirds of the brake fluid must be removed from the master cylinder before…
Q: Technician A says that flare nut or line wrenches should be sued to loosen or tighten brake line or…
A: Flare nut curench is used for loosening a car's fuel line , brake line ,temperature sensor hollow…
Q: Which of the following is true about a brake service? A. It should always include a…
A: Break : A brake is a mechanical device that inhibits motion by absorbing energy from a moving…
Q: Technician a says radial ply tires are more rigid in the sidewall area than bias ply tires.…
A: Technician A is wrong because bias-ply tires have fibres of nylon arranged in a diagonal manner to…
Q: QI: a. List (only) brake types.
A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…
Q: Derive the relation of tarque for internal expanding shae brake?
A: The answer is in the following step
Q: what is the disadvantage of dynamic brakes when compared to mechanical brakes?
A: Mechanical brakes uses the application of friction in order to slow the vehicle or completely stop…
Q: . Technician A says that leaf spring-type rear sus- pensions are subject to axle tramp. Technician B…
A: We are authorized to answer one question at a time since you have mentioned question 4 only so we…
Q: Technician A says that a hard brake pedal on a vehicle with disc brakes can be caused by air in the…
A: Option d is correct. Neither A nor B.
Q: List at least five seperate types of wear and distortion to look for when inspecting brake drums.
A: Wear and Distortion
Q: The types of wear and distortion to look for when inspecting brake drums are
A: Drum Brake The drum brake commonly uses to stop the rotating cylindrical shaped part or wheel by…
Q: What are the risks of working with brake fluid?
A: Brake fluid is generally made with glycol or silicone. Bothe material is dangerous for us.
Q: Duo-servo drum brakes are also known as what type of brake assembly?
A: Drum brakes are commonly used in automobiles .duo servo drum brake system has a pair of brake shoes…
Q: Road test Report is Overhaul all four-wheel brakes and the Universal joints After the maintenance…
A: Option - B , D => After operation is completed the road test report will happen to check the…
Q: Technician A says power brakes are designed with vacuum-assisted units that use engine vacuum.…
A: Most vehicles use vacuum suspended units (vacuum promoters), which utilize a vacuum-fueled sponsor…
Q: Technician A says that the piston seal retracts the caliper piston when hydraulic pressure is…
A: Technician A is correct.
Q: A brake pad is found to be wearing more on one side than the other. Technician A says this is common…
A: Front and rear brake pads normally wear differently. When your vehicle is moving, the forward…
Q: The functions of a splash shield are being discussed: Technician A says that disc brakes will…
A: A splash shield, bolted to the steering knuckle, along with the wheel helps in circulating air over…
Q: The functions of a splash shield are being discussed: Technician A says that disc brakes will…
A: The splash shield is a metallic or plastic part that is placed at the bottom portion of the car. The…
Q: A drum brake is being inspected, and is found to be out-of-round. Technician A says the drum must be…
A: Technician B is correct
Q: During a brake inspection, the inner brake pad is found to be 3mm thick, while the outside pad is…
A: Front and rear brake pads normally wear differently. When your vehicle is moving, the forward…
Q: Discuss the types of brakes along with their figures. Compare disc and drum brakes by discussing…
A: Classification of Brakes 1.On the basis of Power Source Mechanical braking system Hydraulic…
Q: Discuss the types of brakes along with their figures. Compare disc and drum brakes by discussing…
A: Click to see the answer
Q: Discuss the types of brakes along with their figures. Compare disc and drum brakes by discussing…
A: Click to see the answer
Q: Discuss the types of brakes along with their figures. Compare disc and drum brakes by discussing…
A: Click to see the answer
Q: Discuss the types of brakes along with their figures. Compare disc and drum brakes by discussing…
A: (a) Discuss the types of brakes. (b) Along with their figures. (c) Compare disc and drum brakes by…
Q: When examining disc brakes: Technician A visually inspects the rotor and says that the rotor can be…
A: Click to see the answer
Q: Wind Turbine Gearbox & Brake
A: In a wind turbine, a gearbox is used to transfer rotational speed from a low-speed rotor to a…
Q: Explain the purpose of the wheel rim drop center and safety ridges.
A: The purpose of the wheel rim drop center is to allow mounting of the tires, we can easily install…
Q: Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the…
A: The basic function of shift solenoids is to control the pressures within fluid system and they don’t…
Q: Which one of the following theory is considered for the designing of new clutch? Select one: O a.…
A: Uniform wear theory in clutches and bearing. surfaces may be good over the entire surface. It…
Q: Discuss the concept of Brake Specific Fuel Consumption (BSFC)
A: Brake specific fuel consumption – It is the fuel required per unit of work output. It is also…
Q: A clicking noise during transmission/transaxle operation may be an indication of .
A: Given data Why clicking noise during transmission transaxle operation is the indication of ..?
