A voltage, v = 120 sin(377t + 50° ) supplies a current, i = 10 cos( 377t – 60°) to an impedance load. Determine the following: A.) The resistance of the load is ohms. (a) 4.1 (b) 11.28 (c) 12.5 (d) 7.5 B.) The inductance of the load is mH. a.) 10.9 b.) 4.1 c.) 9.10 d.) 1.4 C.) The real power supplied to the load.is watts (a) 260.47 (b) 975.35 (c) 1127.63 (d) 1135.27 D.) The power factor of the circuit is (a) 0.71 lagging (b) 0.17 leading (c) 0.94 leading (d) 0.94 lagging

A voltage, v = 120 sin(377t + 50° ) supplies a current, i = 10 cos( 377t – 60°) to an impedance load. Determine the following: A.) The resistance of the load is ohms. (a) 4.1 (b) 11.28 (c) 12.5 (d) 7.5 B.) The inductance of the load is mH. a.) 10.9 b.) 4.1 c.) 9.10 d.) 1.4 C.) The real power supplied to the load.is watts (a) 260.47 (b) 975.35 (c) 1127.63 (d) 1135.27 D.) The power factor of the circuit is (a) 0.71 lagging (b) 0.17 leading (c) 0.94 leading (d) 0.94 lagging

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
The sending-end voltage in the circuit seen is adjusted so that the load voltage is always 13,800 V(rms). The variable capacitor is adjusted until the average power dissipated in the line resistance is minimum. 1. a) If the frequency of the sinusoidal source is 60 Hz, what is thevalue of the capacitance in microfarads?2. b) If the capacitor is removed from the circuit, what percentageincrease in the magnitude of Vs is necessary to maintain 13,800V(rms) at the load?3. c) If the capacitor is removed from the circuit, what is thepercentage increase in line loss?
Three branches having impedances of 3+j4 Ω, 16−j12 Ω, and−j4 Ω, respectively, are connected in parallel. What are the equivalent(a) admittance, (b) conductance, and (c) susceptance of the parallelconnection in millisiemens? (d) If the parallel branches are excited froma sinusoidal current source where i=8 cosωt A, what is the maximumamplitude of the current in the purely capacitive branch?
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.
A source whose voltage is ? (?) = 50√2 cos (?? + 30 °) ? supplies a load of impedance ? = (4 + ?3) Ω. We want to know: a) the active, reactive and apparent power consumed by the load. b) the power of a capacitor that must be installed in parallel with the load to raise its power factor to 0.97 delayed.
A transmission line with impedance of 0.085 + j 0.32 Ω is used to deliver power to a load. The load is inductive and the load voltage is 200∠0° Vrms at 60Hz. If the load operates at 20 kVA with a power factor of 0.75 determine the real and quadrature power losses in both the load and the line and the source voltage phasor.
Understand ac power concepts, their relationships to one another, and how to calculate them in a circuitA load consisting of a 1.35 kΩ resistor in parallel with a 405 mH inductor is connected across the terminals of a sinusoidal voltage source vg, where vg = 90 cos 2500t V. Find 1. a) the average power delivered to the load,2. b) the reactive power for the load,3. c) the apparent power for the load, and4. d) the power factor of the load.
A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this impedance is a series combination of a 120Ω resistor and another passive component. If the circuit has a sinusoidal voltage source whose frequency is 120 Hz. What is the value of the component in series with the 120Ω resistor? (Note: Express the value assuming a metric scaling of μ(10-6). Provide your answer in decimal form, up to 3 decimal places.)
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are ________ and ____________ , respectively.
A ower system is operating at 1000Mw, 132kV, 50Hz, with 0.8 p.f. laging in parallelwith another line at 750OMW, 132kV, 50Hz with 0.707 p.f. lagging. Both are interconnectedat the station and when the compensating device is on, the overall power factor isimproved to 0.9 lagging. Suggest suitable capacitors, shunt and series. Individual loadsand combined load are to improve power factor to 0.9 in all cases.