A welded cylindrical pressure vessel is shown in the figure. The inner diameter is 600 mm. The wall thickness is 10 mm. Given the gage pressure of 5 MPa, determine (1) the normal stress perpendicular to the weld line and (2) the shear stress parallel to the weld line.

A welded cylindrical pressure vessel is shown in the figure. The inner diameter is 600 mm. The wall thickness is 10 mm. Given the gage pressure of 5 MPa, determine (1) the normal stress perpendicular to the weld line and (2) the shear stress parallel to the weld line.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.13P: : A cylindrical tank with diameter d = 18 in, is subjected to internal gas pressure p = 450 psi. The...

See similar textbooks

Related questions

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

Q: A rectangular plate (0 =22") is formed by welding two triangular plates shown in figure. The plate…

Q: 6 m A= 180 mm 6 m 4 m B.

Q: 3. A tie bar is welded to a plate and it is subjected to axial load, P. The length of the fillet…

A: Given data Length of fillet weld (L) = 200 mm size of fillet (s) = 6 mm stress of the fillet weld…

Q: The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

A: To find: The state of stress at point A on the cross section of pipe at section a-a. Given: The…

Q: 3.3 A steam boiler is to have a 300-mm-diameter hand hole placed on one end. If the maximum internal…

Q: 1.58. A thin-walled cylindrical pressure vessel of 0.3-m radius and 6-mm wall thick- ness has a…

Q: From the figure shown, the tube has an outer diameter of 80 mm and an inner diameter of 70 mm. The…

Q: A bracket is welded to the vertical column by means of two fillet welds as shown in Figure.…

A: Given Data Permissible shear stress is :τ=70 N/mm2 Load is : P=12.5 kN Now the primary shear…

Q: A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown…

A: For solution refer below images.

Q: Q1/ A bracket is welded to a frame by two 10 mm fillet welds as shown in Fig., carries a load of 9…

A: Given: The size of fillet weld, t = 10 mm The length of weld, L = 56 mm The load acting, P = 9 kN…

Q: A tank 10 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

A: Given data height = 10 m diameter = 2 m thickness = 15 mm find the maximum tangential stress and…

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

Q: Find the resultant shear stress at point A & C for the weldment shown in the figure. Leg size of the…

Q: tuation No. 3: The bracket shown is connected by a fillet weld. P1 = 60 kN and P2 = 80 kN and the…

Q: A bracket is welded to the verical column by means of two fillet welds as shown in the figure.…

A: given data: force(F)=150KN=150*103N shear stressτ=70N/mm2 no. of weld(n)=2 size of weld diameter…

Q: Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown…

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

A: Parallel welds is weaker than transverse weld therefore, always assume any fillet weld like a…

Q: The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of…

A: Given Data : Allowable stress = 13600 psi Total actual length Lw = 3 in Total Force F = 9600 lb…

Q: A rectangular plate (0 =20") is formed by welding two triangular plates shown in figure. The plate…

Q: A pipe carrying steam at 3.5 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A…

Q: A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: 3- A bracket, as shown in Fig., carries a load of 10 kN. Find the size of the weld if the allowable…

A: Welding is method of joining two similar or dissimilar metal with or without heat , or with or…

Q: A shaft with two diameters connected by a fillet is shown below. In the diagram, di = 45 mm, d2- 50…

Q: A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate…

Q: A rectangular plate (0 =21°) is formed by welding two triangular plates shown in figure. The plate…

A: Given data θ=21° Compressive stress=2.9 Mpa. Tensile stress=19 Mpa.To determine The normal…

Q: Q2/ According to the figure below find the size of the weld. Take permissible shear stress for the…

Q: 3) -3 m For thin walled pressure vessel: Inner radius =50 em Wall thickness -3 cm P-P'= 0 kN Gage…

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

Q: Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was…

A: Option - B => 0.0241 mm => Total Deformation on the brass

Q: B A bracket shown in the figure is designed to carry a dead weight of W = 15000 N. What sizes of…

Q: 7. For the stressed element in the following figure, determine (a) the value of ty for which the…

Q: A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate…

Q: A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate…

Q: Three solid cylindrical are welded together as shown in Figure 3. Determine the average normal…

Q: Try One - scene 8 of 8 Pin diameter = 24 mm For the pin connection shown, determine the normal…

A: Write the formula for the normal stress acting on the gross area. σgross=PAgross Here, P is the…

Q: welded joint, as shown in figure below, is subjected to an eccentric load of 250 ze of the weld, if…

A: Given Data⇒ Eccentric loading(P)=2500 N Maximum shear stressζmax=50Nmm2

Q: A rectangular plate (0 =20°) is formed by welding two triangular plates shown in figure. The plate…

Q: A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in…

Q: For a given Data of the riveted joint shown in the figure: Given: Diameter of each rivet = 3/4 inch…

A: Given Diameter of each rivet =34 inch=18.796 mmMaximum allowable shear stress of rivet τy =96.53…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

Q: 8-7. A boiler is constructed of 8-mm thick steel plates that are fastened together at their ends…

Q: A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate…

A: GIVEN: σx=-2.3 MPa σy=13 MPa θ=23° TO FIND: The normal stress and Shear stress on the weld plane.

Q: (2) Q1 what the value of P Which are safer on the rivets as shown in figure below. given that :…

Q: A pressurized cylindrical container, as in the figure, is made of 12 mm thick plate as shown in the…

Q: Arectangular cross-section bar is welded to a support by means of fillet welds as shown in Figure…

A: Fillet weld It is a joining process of two metal pieces when they are perpendicular or at an angle…

Q: 4) A welded connection, as shown in Fig. 2, is subjected to an eccentric force of 60 kN in the plane…

Q: 2. A bracket, as shown in Fig. 2, carries a load of 10 kN. Find the size of the weld if the…

Question

Problem A-1 [Pressure Vessel Problem]
A welded cylindrical pressure vessel is shown in the figure.
The inner diameter is 600 mm. The wall thickness is 10 mm.
Given the gage pressure of 5 MPa, determine (1) the normal
stress perpendicular to the weld line and (2) the shear stress
parallel to the weld line.
Weld Line
30°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A spherical tank of diameter 48 in. and wall thickness 1.75 in. contains compressed air at a pressure of 2200 psi. The tank is constructed of two hemispheres joined by a welded seam (see figure). (a) What is the tensile load/ (lb per in. of length of weld) carried by the weld? (b) What is the maximum shear stress rm2Xin the wall of the tank? (c) What is the maximum normal strain e in the wall? (For steel, assume E = 30 X 10 psi and v = 0.29.)
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in shear on the weld is 15,800 psi, the minimum effective length of the weld must be A. 5.4 B 4.9 in C. 4.3 in D 3.9 in.
appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in).
A bracket is welded to the verical column by means of two fillet welds as shown in the figure. Determine the size of the welds, if the permissible shear stress in the weld is limited by 70N/mm^2.
Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown in the figure. Assume that a = 5.0”. Specifications require that the normal and shear stress magnitudes acting in the weld material may not exceed 40 ksi and 25 ksi, respectively. The largest axial load P that can be applied to the aluminum plates is _____ kips.
The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the figure. The tank is manufactured by joining a 6 mm thick steel plate with a helical weld at an angle of 30°. Since the safe shear stress in the direction parallel to the weld seam is 30 MPa, calculate the maximum pressure that can be used in the tank.
Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a double parallel fillet weld as shown in Fig. if the permissible tensile and shear stresses in the weld material are otw MPa and tw MPa respectively and the permissible tensile stress in the plate material are otp MPa, Find the length Li of single transverse fillet weld, if the joint is subjected to both static and fatigue loading. All dimensions in mm.
The figure shows a roof truss and the detail of the riveted connection at joint B. Using allowable stresses of τ= 70 MPa and σb= 140 MPa, how many 22-mm diameter rivets are required to fasten member BC to the gusset plate? Member BE? What is the largest average tensile or compressive stress in BC and BE? Say ABC = 864mm2; ABE = 1780mm2.
A circularbeam, 50 mm in diameter, is welded to support using a fillet weld as in the figure. Determinethe size of the weld, if the permissible shear stress is 100 N/mm2.
A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown below. The pressure in the tank is 2.76 MPa, and an axial load of 133.5 KN is applied to the end of the tank through a rigid bearing plate. Determine the normal stress and shearing stress perpendicular to the weld.
A boiler with an outside diameter of 300 mm, length of 1000 mm and a wall thickness of 10 mm is carrying steam at 4.5 MPa. A seal is inserted between the flange at one end of the boiler and a flat plate is used to cap the end. What circumferential stress is developed in the boiler?