A welded joint, as shown in figure below, is subjected to an eccentric load of 2500 N. Find thesize of the weld, if the maximum shear stress in the weld is not to exceed 50 N/mm2 4. A welded joint, as shown in figure below, is subjected to an eccentric load of 2500 N. Find thesize of the weld, if the maximum shear stress in the weld is not to exceed 50 N/mm².2500 N150X-х 50

Given Data⇒ Eccentric loading(P)=2500 N Maximum shear stressζmax=50Nmm2

Answered: welded joint, as shown in figure below,…

welded joint, as shown in figure below, is subjected to an eccentric load of 250 ze of the weld, if the maximum shear stress in the weld is not to exceed 50 N/mi 2500 N

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.13P: Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses...

See similar textbooks

Related questions

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

Q: The figure shows a roof truss and the detail of the connection at joint B. Member BC and BE are…

Q: n the figure shown, the cutaway view shows a solid aluminum alloy of L= 600mm, A= 707mm^2 and E=…

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

Q: A steel bar of thickness h is welded to a vertical support as shown in the figure. OV The dimensions…

A: To Find : The safe force F in KN. Given : Dimension of perimeter are b=70 mm, c=170 mm, d=70 mm,…

Q: A bolted single lap joint shown in the figure below is designed to join two sheets of wood using a…

Q: Example: 2.7 A hollow circular nylon pipe (see Fig 1-23) supports a load P = 7800 N, which is…

Q: The figure shows a roof truss and the detail of connection at joint I. The allowable stresses are 70…

Q: A welded joint of circular shaft as shown in figure is subjected to an eccentric load of 2.5 kN. If…

Q: A double riveted double cover butt joint in plate of (20) mm thick is made with (25) mm diameter…

A: In plate following stresses are induced 1) Tearing resistance 2) Shearing resistance 3) Crushing…

Q: 4. The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet…

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M 16 cross…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: 4. The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet…

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

A: Option c=25.0 Mpa is correct.

Q: Q2. A plate 120 mm wide and 8 mm thick is to be welded to another plate where the applied static…

Q: Design a rivet that is utilized in a double riveted lap joint which connects two 10 mm thick plates.…

Q: Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure…

A: When it is required to join two rods which are placed under the tensile load and a small amount of…

Q: A welded steel girder having the cross section shown in the figure is fabricated of two b=280…

A: GIVEN :- b=280 mmtf=25mmh=900 mmtw=15mmI=3.91×109 mm4allowable shear stress: ζmax=880 KN/m2we…

Q: 1. Determine the maximum safe load P which may be applied if the shearing stress in the rivets is…

Q: Each weld has an allowable load in shear of 810 kN/m. Calculate the maximum allowable shear force…

Q: As in the figure, a pressurized cylindrical container is made of 12 mm thick plate as shown in the…

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

A: A thin cylinder is a cylinder in which the thickness is the 20th part of the diameter of the thin…

Q: steel:210000 E (MPa) copper:100000 E (MPa) L4 (cm)= 280 L5 (cm)= 255 P1(kN)= 220 P2(kN)= 76 In…

Q: Figure shows a tie bar made of steel. When bolted between A and B double brackets, it is to be…

A: Given Data, P= Tensile load in the bar = 100 KN The bolt is of double brackets, so the shear load…

Q: Q-1 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by four fillet…

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

A: Parallel welds is weaker than transverse weld therefore, always assume any fillet weld like a…

Q: A welded steel girder having the cross section shown in the figure is fabricated of two b=280…

Q: The gap of 0.5 mm in the element given in the figure is formed at 20 C. What is the temperature…

A: Given: ∆l=0.5 mml=0.45 mA=1800 mm2E=73GPaα=12.9×10-6 /°C

Q: A prismatic wing box is constructed of two cylindrical tubes (each of thickness welded to top and…

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

Q: a) The maximum normal stress occurring in the plate, b) Find the shear stress on the M10 bolt and…

Q: A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: Situation 11: As shown in the Figure, three steel wires, each 0.05in? in area, are used to lift a…

Q: Problem #3. The figure below are cables ( circular section) supporting a 36 kN. Find the axial…

Q: The figure shows a horizontal steel bar of thickness h loaded in steady tension and welded to a…

A: Given data: b=49 mmd=48 mmh=5 mmτallow=148 MPa Need to determine the allowable force.

Q: A circular tube of outer diameter d3= 70 mm and inner diameter d2= 60 mm is welded at the right-hand…

Q: 4. The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet…

Q: a. An eccentric load of 95 kN acts on a bracket as shown in Figure 6 at its free end. In the…

A: eccentric load, p=95KNeccentricity e=25+202=35cmallowable sheer stress ζ=10000N/cm2

Q: A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate…

Q: For the joint shown in the figure, if F = 28 kN and do = 12.8 mm, calculate: 7.5 mm F F 12 mm 12 mm…

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

A: Use throat thickness concept to solve this prob, Find allowable F?

Q: (a) A steel bar of thickness h is welded to a vertical support as shown in the figure. What is the…

Q: 70 kN Kaynak dikiş đüzlemi D

Q: What is the Force on the Bronze Material? * Bronze Aluminum Steel 2P 3P P 4P + 0.6 m→« - 0.8 m - 1.0…

A: Given data of various materials are : Change in length of the bar is limited to 2mm.

Q: (a) A steel bar of thickness h is welded to a vertical support as shown in the figure. What is the…

Q: View Policies Current Attempt in Progress The assembly shown in the figure consists of rod (1) and…

Q: 3. A beam-to-column connection is shown in figure below. The beam is a wide flange beam section with…

A: Given: The height of beam, H = 200 mm The width of beam, b = 200 mm The thickness of flange, t1 =15…

Q: Question 2) in the system given in the figure, a distributed load of w = 88 kN / m affects the AB…

A: Given , Distributed load , w =88 KN/m length L =4.1 m Angle made by BC = 56 degrees. Allowable…

Q: A circular beam, 50 mm in diameter, is welded to support using a fillet weld as in the figure.…

Q: A welded steel girder having the cross section shown in the figure is fabricated of two b-180…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

A welded joint, as shown in figure below, is subjected to an eccentric load of 2500 N. Find the
size of the weld, if the maximum shear stress in the weld is not to exceed 50 N/mm2

4. A welded joint, as shown in figure below, is subjected to an eccentric load of 2500 N. Find the
size of the weld, if the maximum shear stress in the weld is not to exceed 50 N/mm².
2500 N
150
X-
х 50

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

: A cylindrical tank with diameter d = 18 in, is subjected to internal gas pressure p = 450 psi. The tank is constructed of steel sections that arc welded circum fereiitially (sec figure). The heads of the tank are hemispherical. The allowable tensile and shear stresses are 8200 psi and 3000 psi, respectively. Also, the allowable tensile stress perpendicular to a weld is 6250 psi. Determine the minimum required thickness /minof (a) the cylindrical part of the tank and (b) the hemispherical heads.
A steel riser pipe hangs from a drill rig. Individual segments of equal length L = 50 ft are joined to get her using bolted flange plates (see figure part b). There are six bolts at each pipe segment connection. The outer and inner pipe diameters are t2= 14 in. and d1= 13 in.; flange plate thickness tf= 1.5 in.; and boll and washer diameters are db= 1.125 in. and dn. = 1.875 in. Find the number n of permissible segments of pipe based on following allowable stresses. (a) The allowable tensile stress in the pipe is 50 ksi. (b) The allowable tensile stress in a bolt is 120 ksi. Find number of segments n for two cases: pipe hanging in air and pipe hanging in seawater.
appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in).
A beam is supported and loaded as shown in the figure. Data: L = 1000 mm, c = 300 mm, f = 100 mm, D = 100 mm, d = 80 mm. The beam consists of different parts that are welded, and the fillet weld size a is 4 mm. The load q is 2 kN/m, and P = 10 kN. Calculate the maximum stress in the welds.
(1) What are the methods used to obtain a good weld when welding steel when the carbon content is high? b) Find the appropriate size and length for the weld joint shown in the figure if the strength is equal to (70000Ib) and the allowable shear stress value is 40ksi and the weld rib dimension is (1/4in)
A circularbeam, 50 mm in diameter, is welded to support using a fillet weld as in the figure. Determinethe size of the weld, if the permissible shear stress is 100 N/mm2.
All-round fillet weld with a steel beam weld thickness a=6 mm and weld seam length shown in the figure welded to the steel column. Forces of 2 kN and 3 kN from the beam end in the horizontal and vertical directions, respectively has been applied. The smallest yield strength of the weld material so that the steel structure has a safety of 2.5. Calculate according to von Mises static damage theory ?
Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown in the figure. Assume that a = 5.0”. Specifications require that the normal and shear stress magnitudes acting in the weld material may not exceed 40 ksi and 25 ksi, respectively. The largest axial load P that can be applied to the aluminum plates is _____ kips.
A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in shear on the weld is 15,800 psi, the minimum effective length of the weld must be A. 5.4 B 4.9 in C. 4.3 in D 3.9 in.
A bracket is welded to the verical column by means of two fillet welds as shown in the figure. Determine the size of the welds, if the permissible shear stress in the weld is limited by 70N/mm^2.
A 3/4-in. horizontal steel bar loaded at constant tension and welded to a vertical support is shown in the figure. Determine the force F if the weld is E6013
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thicknesses shown in the figure. The working stresses are 70 MPa for shear in the rivets and 140 MPa for bearing stress due to the rivets. How many 20-mm-diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE?