Answered: 3- A bracket, as shown in Fig., carries…

3- A bracket, as shown in Fig., carries a load of 10 kN. Find the size of the weld if the allowable shear stress is not to exceed 80 MPa. 20 kN 100> -200- All dimensions in mm. OSI

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.13P: Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses...

See similar textbooks

Related questions

Q: 410 N 30° 45° 200 N 10 10 mm

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

Q: 3. A tie bar is welded to a plate and it is subjected to axial load, P. The length of the fillet…

A: Given data Length of fillet weld (L) = 200 mm size of fillet (s) = 6 mm stress of the fillet weld…

Q: Example: 2.7 A hollow circular nylon pipe (see Fig 1-23) supports a load P = 7800 N, which is…

Q: 1.58. A thin-walled cylindrical pressure vessel of 0.3-m radius and 6-mm wall thick- ness has a…

Q: A welded joint of circular shaft as shown in figure is subjected to an eccentric load of 2.5 kN. If…

Q: 1. Question: With a pin on the AB beam A and a short lever BC as shown in the figure is supported.…

A: Given dataDiameter of the pins ar A,B and C d = 18mmLoad P = 30kNAngle α= 600Pin =ADetermine the…

Q: ASAP

Q: 10/.. find the shear stress in bolts 4 80 kN 80 kN -O- O--O- 300 mm

A: Write the expression for the load acting on the riveted joint.

Q: 130 mm 25 mm 25 mm FIG. P1.30, P1.31 1.31 Assume that the axial load P applied to the lap joint is…

Q: Q1/ Figure below shows a welded steel bracket loaded by a static force F. Estimate the safety factor…

Q: Q1/ A bracket is welded to a frame by two 10 mm fillet welds as shown in Fig., carries a load of 9…

A: Given: The size of fillet weld, t = 10 mm The length of weld, L = 56 mm The load acting, P = 9 kN…

Q: Q2. A plate 120 mm wide and 8 mm thick is to be welded to another plate where the applied static…

Q: 2) Design the fillet weld for direct shear connection for the angle loaded as shown in the figure.…

A: INTRODUCTION: The fillet weld and the butt weld are two different types of weld joints, according to…

Q: Choose True or False. a) Consider the truss below that is made up of elements (1) and (2). TRUE or…

A: According to the details provided in the question, we need to calculate the TRUE / FALSE condition.

Q: The central plates a in Fig.12 of the text are 9/16 in. thick and 9 in. wide. The diameter of the…

Q: Find the position and the value of the maximum stress for the weld joint shown in the figure. Assume…

A: Introduction: The load-bearing capability of a weld relates to how much load it can withstand before…

Q: Q-1 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by four fillet…

Q: 125 x 95 x 10 mm angle is welded to a frame by two 10 mm fillet welds, as shown in Figure bellow. A…

A: Given that, Thickness of toe=10 mm,

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

A: Parallel welds is weaker than transverse weld therefore, always assume any fillet weld like a…

Q: 1. A 125 x 95 x 10 mm angle is welded to a frame by two 10 mm fillet welds, as shown in Fig. 1. A…

Q: A horizontal force P= 110,976 N is pushing an inverted L-frame supported by a foundation at the…

Q: details are given, rivets and plates. Find the maximum shear, crush and tear (tensile) stresses.…

Q: The figure shows a horizontal steel bar of thickness h loaded in steady tension and welded to a…

A: As per the guidelines we have to solve only first question. So kindly you post the second question…

Q: A shaft with two diameters connected by a fillet is shown below. In the diagram, di = 45 mm, d2- 50…

Q: 1. A picce of wire 10-in long is tied vertically. The wire has a diameter of 0.1-in and is used to…

Q: Specify the weld size for the case where the maximum allowable shear stress is 18 kpsi.

Q: A rectangular plate (0 =21°) is formed by welding two triangular plates shown in figure. The plate…

A: Given data θ=21° Compressive stress=2.9 Mpa. Tensile stress=19 Mpa.To determine The normal…

Q: A rectangular plate with a hole is shown in fig that carries a tensile load. Stress value calculated…

A: Given that A rectangular plate with a hole is shown in fig that carries a tensile load. Stress…

Q: The figure shows a welded steel bracket loaded by a static force F. Estimate the load F if the…

A: .

Q: ods were stress-free. Determine the load in each rod if W = 51.29 KN. listance into mm. | Figure…

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

Q: cross section, side length b, and wall thickness t. The second is a round of diameter b and wa…

Q: 1-Two rivets holds three sheets of steel together, and is loaded as shown below. If the maximum…

Q: welded joint, as shown in figure below, is subjected to an eccentric load of 250 ze of the weld, if…

A: Given Data⇒ Eccentric loading(P)=2500 N Maximum shear stressζmax=50Nmm2

Q: I- The two plate-shaped parts given below are joined with a rivet. Examine this figure and formulate…

A: Part (1): For this case, total shear force is transmitted through highlighted single red face (as…

Q: A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in…

Q: The figure shows a flat hanger bar for supporting shop equipment in a factory. The bar is fixed to a…

A: Given data, Width of hanging bar, w = 1.5 in to 3 in Diameter of the bolt, d = 1 in From the…

Q: Find the smallest and safestd of the link as shown on the figure, if the working stress is equal to…

A: Find the smallest diameter

Q: (2) Q1 what the value of P Which are safer on the rivets as shown in figure below. given that :…

Q: Arectangular cross-section bar is welded to a support by means of fillet welds as shown in Figure…

A: Fillet weld It is a joining process of two metal pieces when they are perpendicular or at an angle…

Q: A welded cylindrical pressure vessel is shown in the figure. The inner diameter is 600 mm. The wall…

Q: Q-1 The attachment shown carries a static bending load of 15 kN. The attachment length, 4, is 260…

A: Static bending load acting is 15 kN Attachment length 260 mm

Q: A cylindrical bar shown in the figure below has axial loads applied as illustrated. Calculate the…

A: As per given We have to find stress in bar of section AB, BC and CA

Q: A plate 70mm wide and 15mm thick is joined with another plate by a single transverse weld and a…

A: According to the given information plate 70 mm wide and 15 mm thick, maximum tensile stress 60…

Q: 2. A bracket, as shown in Fig. 2, carries a load of 10 kN. Find the size of the weld if the…

Q: Find the smallest and safest d of the link as shown on the figure, if the working stress is equal to…

A: Given Working stress, SN = 20 MPa Force, FN = 10 kN Find Diameter, d

Q: A 40mm thick steel bar that is fabricated by welding two parts together is shown below. Being…

A: Given :-

Question

3- A bracket, as shown in Fig., carries a load of 10 kN. Find the size of the weld if the
allowable shear stress is not to exceed 80 MPa.
20 kN
100>
-200-
All dimensions in mm.
150

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld cannot exceed 3 in. If the weld must transmit a total force equal to 9600 lb, it’s size should be A. 1/2 in. B. 3/8 in. C. 5/16 in. D. 1/4 in.
A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in shear on the weld is 15,800 psi, the minimum effective length of the weld must be A. 5.4 B 4.9 in C. 4.3 in D 3.9 in.
The figure shows a solid 2-inch diameter roller that is attached to the wall by means of a permanent clamping. Specify the weld size for the case where the maximum allowable shear stress is 18 kpsi.
appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in).
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?.
(1) What are the methods used to obtain a good weld when welding steel when the carbon content is high? b) Find the appropriate size and length for the weld joint shown in the figure if the strength is equal to (70000Ib) and the allowable shear stress value is 40ksi and the weld rib dimension is (1/4in)
If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the diameter (mm) of the A premium?
Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a double parallel fillet weld as shown in Fig. if the permissible tensile and shear stresses in the weld material are otw MPa and tw MPa respectively and the permissible tensile stress in the plate material are otp MPa, Find the length Li of single transverse fillet weld, if the joint is subjected to both static and fatigue loading. All dimensions in mm.
A circularbeam, 50 mm in diameter, is welded to support using a fillet weld as in the figure. Determinethe size of the weld, if the permissible shear stress is 100 N/mm2.
Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN Please send the solution within half an hour and thank you
A welded joint, as shown in figure below, is subjected to an eccentric load of 2500 N. Find thesize of the weld, if the maximum shear stress in the weld is not to exceed 50 N/mm2
Find the interal normal stress in all relevant segments of the bar in the picture.