A wind turbine gives the folowing dataBlade length= 59 m.Wind speed = 135 m/sAir density = 1229 Kg/mPower coefficent = 045Assuming equal efficiencies tor gearbor and generator fme Power output from wind turbine, Pis 11 MW, then feda) Rotor Power Output. Pr in MWb) Wind Power P, in MWd Effciency of Generator eRotor Power Output, Prin MWWind Power, Pa in MwEfficency of Generator

Given Blade length, L=r=59 m wind speed, V=13.5 m/s Air density (ρ) =1229 kg/m3 power coefficient…

A wind turbine gives the folowing data Blade lengtha 59 m. Wind speed = 13.5 m/s Air dersity = 1229 Kgim Power coefficient 045 Assuming equa effcencies tor gearbor and generator he Power output from wind turbine, Pis11 Mw then find a) Rotor Power Output Py in MW b) Wind Power P, in MW O Effcency of Generator i

A wind turbine gives the folowing data Blade lengtha 59 m. Wind speed = 13.5 m/s Air dersity = 1229 Kgim Power coefficient 045 Assuming equa effcencies tor gearbor and generator he Power output from wind turbine, Pis11 Mw then find a) Rotor Power Output Py in MW b) Wind Power P, in MW O Effcency of Generator i

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.21P: An industrial plant consisting primarily of induction motor loads absorbs 500 kW at 0.6 power factor...

See similar textbooks

Similar questions

A440V,22.5-hp,50Hz,3-phase,4-pole,star-connectedinductionmotorhasthefollowing impedances in ohms per phase referred to the stator circuit:R1 = 0.55Ω R2 = 0.35ΩX1 = 1.105Ω X2 = 0.456Ω XM = 27.1ΩThe total rotational losses are 1105 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.3% at the rated voltage and rated frequency, calculate:d) Electrical power, e) Output power,f) Efficiency.
A440V,22.5-hp,50Hz,3-phase,4-pole,star-connectedinductionmotorhasthefollowing impedances in ohms per phase referred to the stator circuit:R1 = 0.55Ω R2 = 0.35ΩX1 = 1.105Ω X2 = 0.456Ω XM = 27.1ΩThe total rotational losses are 1105 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.3% at the rated voltage and rated frequency, calculate:g) The shaft torque of the motor at rated load
The wind turbine gives the following data: Blade length, l = 49 m, Wind speed, V= 32 Km/Hr, Air density, ρ = 1.23 kg/m3 , Power Coefficient, Cp = 0.4, Calculate the power available in the rotor in Watts. 60772464.72 W 394985.47 W 1302564.83 W 151931161.80 W
A turbine has a power coefficient equal to 0.3 when the wind speed is 7 m / s. This turbine is coupled, through a multiplier, to an asynchronous generator of rotor in cage which, in turn, is connected to the distribution network. Considering the data, Air density: 1.25 kg / m3 Blade radius: 15 m Multiplier coefficient: 50 Number of asynchronous generator's pole pairs: 2 Mains frequency: 60 Hz 1% slip Calculate the speed of the turbine rotor (rpm). Is it considered fast or slow?
If the Reactance of the cylindrical rotor machine connected to an infinite bus bar is double that of the external reactance of 0.5.p.u. If the power angle is 35°, real power output is 0.8, compute the excitation voltage, and for the same power output, if the load angle is reduced by 10 degrees, find the external reactance to achieve this.
Define derating, why must a 60Hz generator be derated if it is to be operated at 50Hz? Find percentage of derating done. (4) A generator connected with an infinite bus bar, the frequency indicator shows that frequency is decreasing from 50Hz. What action you will take for restoration of frequency. (2) A generator is loaded with certain load, and its voltage regulation is very poor. What are various ways by which you can improve its regulation? (2)
Four industrial centers are located at the corners of a square of 35300 m side. The loads are 430000 W, 600000 W, 220000 W and 740000 W respectively. Determine the best Y coordinate location of the substation . The reference point of load is 220000 W. Coordinate of Y in KM =
ı know answer but how? z=2, p=1,n=1 and system is unstable
The data for a wind turbine is given below: Wind speed = 14 meters/sec, Length of blade = 10 meter Refer to the above wind turbine choose the correct statement a. The wind rotor swept area is 40square meters. b. The wind rotor swept area is 314 square meters. c. The wind rotor swept area is 31.4 square meters. d. The wind rotor swept area is 62.4 square meters.
A Turgo type hydro-electric plant uses a 92% efficiency generator to produce its rated output of 32.5 MW. It was observed during its operation that the mechanical loss is 4.25 MW. Also, from the penstock down to the turbine, 14.3% hydraulic head loss and 8.9% leakage loss occurs which are equally distributed and based on the parameters at the dam. The average elevation from the headrace to the jet centerline is 40 m and from the tailrace to the jet centerline is 4.5 m. compute the following: a. Power by the turbine, kW b. Volume flow rate at the source, m3/s c. Power by the jet, kW d. Mechanical Efficiency, %
A 800 V, 120kVA, 3-phase, 50 Hz, salient-pole synchronous generator is used in a hydroelectric dam, converting water flow into electricity via a turbine. The reactance values (Xd and Xq) are 1.95 Ω and 1.10 Ω, respectively and the terminal current is measured to be 95 A at a power factor of 0.85 lagging. The armature resistance can be considered to be negligible (Ra =0). a) Draw the phasor diagram of the generator, b) Compute the generated voltage (Êaf) when the generator delivers its rated kVA at 0.85 lagging power factor and rated terminal voltage. ANS=Eaf=578.05exp(j9.75°)
A single phase autosequential CFI is fed from a 220 Vde source, R_{L} = 10Omega the thyristor turn off tq time equals to 20 us and frequency is 50 Hz. Determine suitable value of source inductance assuming a maximum current change di/dt of 0.5A per cycle. Neglecting all losses, calculate able the value of operating capacitor C.