Q1/ Two involute gears of 20° pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is 2. If the pitch expressed in module is 5 mm and the pitch line speed is 1.2 m/s, assuming addendum as standard and equal to one module, find: 1. The angle turned through by pinion when one pair of teeth is in mesh ; and 2. The maximum velocity of sliding.

Q1/ Two involute gears of 20° pressure angle are in mesh. The number of teeth on pinion is 20 and the gear ratio is 2. If the pitch expressed in module is 5 mm and the pitch line speed is 1.2 m/s, assuming addendum as standard and equal to one module, find: 1. The angle turned through by pinion when one pair of teeth is in mesh ; and 2. The maximum velocity of sliding.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the gear train illustrated in Figure, determine the output speed and direction of rotation if the input shaft rotates at 1490 rpm clockwise. Gears A to D have a module of 1.5 and gears E to H a module of 2. TA=20 teeth, TD=38 teeth, TE=18 teeth, TG=18 teeth, TH=30 teeth, dB=67.5mm, dC=27 mm and dF =56 mm.
Solve this problem in spur gearsA 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressureangle and a diametral pitch of 32. Determine the base pitch and the contact ratio. Also,calculate theaddendum, dedendum, circular pitch, tooth thickness, and the base diameter for the pinion and gear. Ifthe center distance isincreased by 0.125 in., what are the new valuesfor thecontact ratio and thepressureangle with complete solution and write in hand writing thank you
Colegio de Muntinlupa fabricated a pair of spur gear 2.5 module (20° full depth involute tooth) and to be mounted on shafts with a centerline distance of 90 mm. The speed ratio required is 3:1. Determine the following: a. Pitch diameter of pinionb. Pitch diameter of gearc. Number of teeth of piniond. Number of teeth of geare. Circular pitch of pinionf. Circular pitch of gearg. Addendumh. Dedendumi. Clearancej. Whole depthk. Working Depthl. Backlashm. Tooth thicknessn. Tooth space widtho. Outside diameter of pinionp. Outside diameter of gearq. Root diameter of pinionr. Root diameter of gears. Base diameter of piniont. Base diameter of gear
Two straight-toothed bevel gears mesh with a shaft angle of 90° and a diametral pitch of 5. The pinion has 20 teeth, and the gear ratio is 2:1. The addendum and dedendum are the same as for 20 stub teeth. For the gear, determine the pitch radius, cone angle, outside diameter, cone distance, and face width.
A 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20°pressure angle and a diametral pitch of 32. Determine the base pitch and the contact ratio.Also,calculate the addendum, dedendum, circular pitch, tooth thickness, and the base diameterfor the pinion and gear. If the center distance is increased by 0.125 in., what are the newvaluesfor the contact ratio and the pressure angle.
A pair of gear/pinion of 42 tooth and 18 tooth with a diametral pitch of 0.7874 teeth/cm and the addendum is 0.8/p and dedendum 1/p. The gear pressure angle is 200 . Compute the center distance of the pair of gears in meters.
Find the diameter of each gear using one simple gear train with 4 gears that work as a speed reducer with a ratio of 5:1 Input of 100 rpm, Output of 20 rpm. Consider number of teeth as: N1=20 N2=40 N3=80 N4=100 Use module of 2
8.7 A pair of involute gears with 16° pressure angle and 6 mm module is in mesh. The number of teeth on pinion is 16 and its rotational speed is 240 r.p.m. When the gear ratio is just 1.75, find, in order that the interference is just avoided, (a) the addenda on pinion and gear wheel (b) the length of path of contact, and (d) the maximum velocity of sliding of teeth on either side of the pitch point. (DAV Indore, 1989) (Ans. a, 9.6 mm; a 4.2 mm; 35.41 mm; V = 95.58 cm/s) %3D
The total conversion rate of a two-stage gearbox is 53, the conversion rate of the second stage is 1.5 times the conversion rate of the first stage. If the number of teeth of the gear mounted on the input shaft is z1=27 and the number of teeth of the pinion of the second stage is z3=33, how many teeth are the gear z2 of the first stage?
1. A worm gear has 52 teeth and a diametral pitch of 6. It mates with a triple threaded worm that rotates at 1750 rpm. The pitch diameter of the worm is 50 mm. a) Compute the circular pitch, b) The axial pitch, c) The lead and the lead angle, d) The pitch diameter of the worm gear,
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Calculate the contact ratio ε with the standard center distance a, 68.75mm. ε=( )
7. The following data relate to a pair of 20° involute gears in mesh : Module = 6 mm, Number of teeth on pinion = 17, Number of teeth on gear = 49; Addenda on pinion and gear wheel = 1 module. Find : (a) The number of pairs of teeth in contact (b) The angle turned through by the pinion and the gear wheel when one pair of teeth is in contact (c) The ratio of sliding to rolling motion when the tip of a tooth on the larger wheel (i) is just making contact (ii) is just leaving contact with its mating tooth (iii) is at the pitch point.