(a) Write down the slip gauge selection for 162.83 mm using standard BM1-447-11 slip gauge set shown below. Slip gauge set for MITUTOYO BM1-447-11 Range (mm) Increment Number (mm) of pieces 1.01 -1.19 0.01 19 1.2 -1.9 0.1 8 1.0 - 9.0 1.0 9. 10.0 - 100.0 10 10 1.005 1 Total Number of Slip Gauge 47 (b) A grinding wheel is written with the following specifications Q C 16 G 7 B 18. Identify the specification "C", "G', "7", "B" on the grinding wheel and define any two.

(a) Write down the slip gauge selection for 162.83 mm using standard BM1-447-11 slip gauge set shown below. Slip gauge set for MITUTOYO BM1-447-11 Range (mm) Increment Number (mm) of pieces 1.01 -1.19 0.01 19 1.2 -1.9 0.1 8 1.0 - 9.0 1.0 9. 10.0 - 100.0 10 10 1.005 1 Total Number of Slip Gauge 47 (b) A grinding wheel is written with the following specifications Q C 16 G 7 B 18. Identify the specification "C", "G', "7", "B" on the grinding wheel and define any two.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Using slip gauge set (BM1- 447 -11) shown in the tabular column(below) select suitable slip gauges of the 44.73 mm work piece size
Cal. the permeability number of a sand specimen if it takes 75s to pass 2000 cm3 of air at a pressure of 6 g/cm2 through the standard sample.
(i) An engine shaft running at 4.5r.p.s. is required to drive a machine shaft by means of a belt. The pulley on the engine shaft is of 2m diameter and that of the machine shaft is 1m diameter. If the belt thickness is 7mm.Determine the speed of the machine shaft, when 1. There is no slip 2. There is a slip of 3%
BSEN10045 is British standard for Brinell Hardness test Select one: True False
Explain the principle used in Residual Stress Measurement with advanatages, disadvantages and applicaions
Annealed low-carbon steel has a flow curve with strength coefficient = 80,000 lb/in2 and strain-hardening exponent = 0.25. A tensile test specimen with gage length = 2.0 in is stretched to a length = 3.5 in. Determine the flow stress and average flow stress that the metal experienced during this deformation. use correct stratgy and correct E 0.55962
Determine tolerance value and limit dimension of the rod which a diameter is ∅6 mm, according to the g6 limit deviation (∅47g6). es=-5.8 mkm, ei=-15.24 mkm. Determine the basic size, tolerance and limit dimensions.
1. On the drawing attached, before any geometric controls are applied, what is the coaxility tolerance that is implied between the diameters?
Determine the indentation diameter and the surface area of indentation of a copper material subjected to a Brinell hardness test with a test force of 7.3 kN using a hardened steel ball indentor of 11 mm. Take the Brinell Hardness Number as 948. Solution: i) Indentation Diameter (in mm) = ii) Surface Area of Indentation (in mm2) =
These are material used for lining of friction surfaces of a clutch should have the followingcharacteristics: 1.It should have a high and uniform coefficient of friction.2. It should not be affected by moisture and oil.3. It should have the ability to withstand high temperatures caused by slippage.4. It should have high heat conductivity.5. It should have high resistance to wear and scoring. Can you explain why these characterictic are important?
The following data were obtained from the tensile test of Aluminum alloy. The initial diameter of testspecimen was 0.505 inch and gauge length was 2.0 inch. Plot the stress strain diagram and determine(a) Proportional Limit (b) Modulus of Elasticity (c) Yield Stress at 0.2% offset (d) Ultimate Stress and(e) Nominal Rupture Stress.
Determine the young’s modulus value of each material testing, and indicate which material is the shaft made from. Use the experimental data provided from the torsion test conducted on the shafts from three different materials. The materials included in this test are Aluminium, Brass, and Steel. Ensure you work through the provided tables and indicate which results correspond to which material. Dimensions Diameter (mm) 6 Length (mm) 77 J= (π ×D^4)/32 G= TL/θJ Degree Radian Material 1 Material 2 Material 3 1 0.017453 1.11 1.83 0.47 1.5 0.02618 1.47 2.46 0.76 2 0.034907 1.84 3.2 1.01 2.5 0.043633 2.72 3.93 1.32 3 0.05236 2.7 4.72 1.65 3.5 0.061087 3.11 5.54 1.99 4 0.069813 3.36 6.4 2.32 4.5 0.07854 3.98 7.27 2.66 5 0.087267 4.41 8.18 3 5.5 0.095993 4.84 9.15…