A1 6. The viscosity function for a given material is measured under simple shear andfound to ben = 5450y-0.34where shear rate, ý, is in units of s1 and viscosity, n, is in Pa.s. What is thepower-law index n? What are the units of 5450? Recall for Newtonian fluidsunder shear: T = ný and for non-Newtonian fluids: T = my", n is the power-lawindex.

Answered: Image /qna-images/answer/872712df-23a7-45ab-b5c5-31701331d96f.jpg

e viscosity function for a given material is measured under simple shear and nd to be 7 = 5450y-0.34 re shear rate, ý, is in units of s' and viscosity, n, is in Pa.s. What is the er-law index n? What are the units of 5450? Recall for Newtonian fluids er shear: 1 = ný and for non-Newtonian fluids: T = my", n is the power-law x.

e viscosity function for a given material is measured under simple shear and nd to be 7 = 5450y-0.34 re shear rate, ý, is in units of s' and viscosity, n, is in Pa.s. What is the er-law index n? What are the units of 5450? Recall for Newtonian fluids er shear: 1 = ný and for non-Newtonian fluids: T = my", n is the power-law x.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

The spherical particle of unit density falls freely in air with a constant velocity of 0.50 cm/sec. The viscosity coeffiecient of the air 0.000180 poise. Using Stoke’s Law, find the radius of the particle.
(Permeability). A cylindrical core sample of 1 cm length and 1 cm2 cross-section has upstream and downstream pressures of 2 atm and 1 atm, respectively, during steady state flow of water at 0.997 g/s at room temperature. Calculate the permeability of the core. Note: Water @ 25°C, viscosity = 1 cp, density of water = 0.997 g/cm3. SHOW SOLUTIONS PLS ASAP
The diagram below, fig 1, shows the results of a viscosity v’s temperature for ayellow ink.The company datasheet extract, fig 2, shows the manufacturers specification.With your knowledge of viscosity v’s temperature and the information in the datasheet explain some reasons for the discrepancies
Cal. the permeability number of a sand specimen if it takes 75s to pass 2000 cm3 of air at a pressure of 6 g/cm2 through the standard sample.
Calculate the individual uncertainties associated for measuring this velocity from the provide individual values given by the manufacture. Then determine the design stage instrument uncertainty. Which uncertainty (or which couple of uncertainties) is the most significant contributor? You attempt to determine the validity of a mass balance in your lab by repeatedly placing 100 g calibration weight on it. Fifteen readings were obtained with values of 101.2, 100.1, 99.8, 100.5, 101.1, 100, 100, 99.6, 101.5, 100.8, 100.9, 100.3, 99.8, 100.5, and 100.9 Estimate the bias error and the maximum precision error of the measurements
A certain liquid at 20 deg.C has a viscosity of 0.000651 Pa.s. What shear stress is required to deform this fluid at the shear rate of 4900 per second?
explain briefly the significance of each of the following parameters:
1. In Buckingham π theorem, if n is the number of variables and m is the number of basic dimensions, the number of independent dimensionless parameters would be,A. (m – n) B. (n – m) C. (m + n) D. (n/m)
η =2gr^2(ps−pl)/ 9v State the value of the viscosity and error on the value obtained in your experiments. Youshould show the formula derived for calculating the error on viscosity. pl (density of liquid)= 1294.164 ps ( density of solid sphere)= 8404 kg/m^3 v= 0.0479 +- 1.16x10^-3 m/s r= 0.0024325m error for radius is 1.65 x 10^-3 all values are in si units.
A tentative rule was given about tipping in Testing Experiment Table 8.4, where if a vertical line passing through the object's center of mass is within the object's area of support the object does not tip. According to the rule, the full box of crackers in the following experiment, which has a width of 13 cm and a height of 20 cm, was seen to tip at an angle of: θc=tan−1(13 cm/20 cm)=33∘θ According to the rule, at what angle will a box with the left half filled with crackers begin to tip? Assume the box is light-weight and that the contents remain in the configuration in
Alplas Plastics uses an extruder in which the barrel diameter = 0.4 m and length = 6.0 m. The extruder screw rotates at 65 rev/min; it has channel depth = 0.02 m and flight angle = 16°. The plastic melt has a shear viscosity = 85 Pa-s. Determine: (a) Qmax and pmax; (b) the shape factor Ks for a circular die opening in which Dd = 0.009 m and Ld = 0.03 m; and (c) the values of Q and p at the operating point
1. On the drawing attached, before any geometric controls are applied, what is the coaxility tolerance that is implied between the diameters?