An assembly line requires two components: gadjits and widjits. Gadjits are produced by center 1 and widjits are produced bycenter 2. Each unit of the end item, called a jit-together, requires 3 gadjits and 2 widjits. The daily production quota on theassembly line is 775 jit-togethers. The container for gadjits holds 85 units. The policy variable for center 1 is set at 0.08. Theaverage waiting time for a container of gadjits is 0.08 day, and 0.05 day is needed to produce a container. The container forwidjits holds 55 units, and the policy variable for center 2 is 0.05. The average waiting time per container of widjits is 0.16 day,and the time required to process a container is 0.23 day.a. How many containers are needed for gadjits?b. How many containers are needed for widjits?containers. (Enter your response rounded up to the next whole number.)containers. (Enter your response rounded up to the next whole number.)

Given the information shown below, Given InformationGadjitsRequired units3Container size…

Answered: a. How many containers are needed for…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

An assembly line requires two components: gadjits and wi-djits. Gadjits are produced by center 1 and widjits by center 2.Each unit of the end item, called a jit-together, requires three gadjits and two widjits, as shown in Figure 6.13. The dailyproduction quota on the assembly line is 800 jit-togethers. The container for gadjits holds 80 units. The policy variablefor center 1 is set at 0.09. The average waiting time for a con-tainer of gadjits is 0.09 day, and 0.06 day is needed to producea container. The container for widjits holds 50 units, and thepolicy variable for center 2 is 0.08. The average waiting timeper container of widjits is 0.14 day, and the time required toprocess a container is 0.20 day.a. How many containers are needed for gadjits?b. How many containers are needed for widjits?
Furniture Face Lift refinishes old wood furniture. Their process for refinishing chairs has 9 workers and 4 stations. Each chair starts at the Stripping station, then goes to Priming, then to Painting and finally to Inspection. Where there are multiple workers within a station, each worker works independently on his/her own chair. Assume inventory buffers are allowed between each station. Station Staffing Processing time (hours per chair per worker) Stripping 3 2.5 Priming 2 1.5 Painting 3 1.75 Inspection 1 0.8 A truck loaded with 10 chairs arrives. How many hours will it take them to complete these 10 chairs?(The accuracy should be of two digits after the decimal places.)
If mixed model scheduling is used, how many of each model will be produced before the cycle is repeated, if the master production schedule calls for 55 units of product A, 40 units of product B, and 20 units of product C per seven-hour shift? Group of answer choices 5 of A, 5 of B, 5 of C 11 of A, 8 of B, 4 of C 22 of A, 16 of B, 8 of C 55 of A, 50 of B, 20 of C Please do fast ASAP
A company produces two products: A and B. Prod-uct A sells for $11 per unit and product B sells for $23 per unit. Producing a unit of product A requires two hours on assembly line 1 and one unit of raw ma-terial. Producing a unit of product B requires two units of raw material, one unit of A, and two hours on as-sembly line 2. On line 1, 1300 hours of time are avail-able, and 500 hours are available on line 2. A unit of raw material can be bought (for $5 a unit) or produced(at no cost) by using two hours of time on line 1.a. Determine how to maximize profit.b. The company will stop buying raw material whenthe price of raw material exceeds what value? (UseSolverTable.)
The Goodparts Company produces a component that is subsequently used in the aerospace industry. The component consists of three parts (A, B, and C) that are purchased from outside and cost 35, 30, and 10 cents per piece, respectively. Parts A and B are assembled first on assembly line 1, which produces 185 components per hour. Part C undergoes a drilling operation before being finally assembled with the output from assembly line 1. There are, in total, six drilling machines, but at present only three of them are operational. Each drilling machine drills part C at a rate of 80 parts per hour. In the final assembly, the output from assembly line 1 is assembled with the drilled part C. The final assembly line produces at a rate of 205 components per hour. At present, components are produced eight hours a day and five days a week. Management believes that if the need arises, it can add a second shift of eight hours for the assembly lines. The cost of assembly labor is 30 cents per part for…
In a large microelectronics plant, the assembly cell for circuitboards has a demand for 200 units an hour. Two feeder cellssupply parts A and B to the assembly cell (one A and one Bfor each board). Standard containers that look like dividedtrays are used. A container will hold 20 As or 10 Bs. It takes10 minutes to fill up a container with As and 20 minutes tofill up a container with Bs. Transit time to the assembly cell is5 minutes for both A and B. No safety factor is used. Set up akanban control system for the assembly process.
a chain saw requires 4 hours of assembly and wood chipper 3 hours.A maximum of 36 hours of assembly time is available.The profit is $150 on a chain saw and 220 on a chipper.How many of each should be assembled for maximum profit?
Jason Carter works for a producer of soaps that come inpackages of 6 each. His job is to fi ll the packages with soap, andhe is expected to process 30 packages an hour. Th e facility whereJason works uses a kanban production system in which eachcontainer holds 5 packages of soap. It takes 20 minutes to receivethe packages he needs from the previous workstation. How manykanbans are needed for the fi lling process?
A computer recycler sells computer enclosures to a computer remanufacturer. To meet monthly expected demand, the remanufacturer needs 2.000 enclosures. The recycler utilizes a four-step disassembly process with scrap rates given as follows: d1=0.08, d2=0.05, d3=0.05, and d4=0.03. How many computers must be recycler receive each month in order to meet the remanufacturer’s demand?
Flores Manufacturing, Inc., is moving to kanbans tosupport its electronic-boa rd assembly lines. Detennine the size of thekanban for subassemblies and the number of kanbans needed. F)cSetup cost = $25Annual holding cost = $200 per subassemblyDaily production = 400 subassembliesAnnual usage = 50,000 (=50 weeks X 5 days eachX daily usage of200 subassemblies)Lead time = 6 daysSafety stock = I day's production of subassemblies
Rene steering makes 100 000 steering wheels per month. The firm works for 20 days in month, each day comprises of three 8 hour shifts. An assembly worker produces 10 steering wheels per hour; the firm needs ----- number of workers for each shift?
In a sandwich production factory, making each ham and cheese sandwich consists of a number of activities which totally take 7 minutes. The production line for ham and cheese sandwich has five workers who work 12 hours a day. What is the maximum number of ham and cheese sandwiches they canmake in this production line?a) 465 b) 425c) 612 d) 514e) 102

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS

a. How many containers are needed for gadjits? b. How many containers are needed for widjits? containers. containers.