Part A Three identical boards are bolted together to form the built-up beam. Euch bolt has a shear strungth of 1.2 kip and the bolls are spaced at a distance of s= 7 in. (Eigure 1) If the wood has an allowable shear stress of Talow- 450 psi, determine the maximum allowable Intemal shear V that can act on the beam. Express your answer to three significant figures and include the appropriate units.

Part A Three identical boards are bolted together to form the built-up beam. Euch bolt has a shear strungth of 1.2 kip and the bolls are spaced at a distance of s= 7 in. (Eigure 1) If the wood has an allowable shear stress of Talow- 450 psi, determine the maximum allowable Intemal shear V that can act on the beam. Express your answer to three significant figures and include the appropriate units.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The beam is made of Douglas fir having an allowable bending stress of sallow = 1.1 ksi and an allowable shear stress of tallow = 0.70 ksi. Determine the width b if the height h = 2b.
The beam is made of timber that has an allowable bending stress of σallow=6.5MPaσallow=6.5MPa and an allowable shear stress of τallow=500kPaτallow=500kPa. Determine its height if it is to be rectangular and have a height-to-width ratio of 1.09. h=? Determine its width. Express your answer with the appropriate units. b=?
Determine the maximum shear force V that the strut can support if the allowable shear stress for the material is tallow = 40 MPa.
Determine the shear stress at points A and B of the web, when the beam is subjected to a shear force V = 15 kN. Consider w = 125 mm
The joists of a floor in a warehouse are to be selected using square timber beams made of oak. If each beam is to be designed to carry 90 lb>ft over a simply supported span of 25 ft, determine the dimension a of its square cross section to the nearest 14 in. The allowable bending stress is sallow = 4.5 ksiand the allowable shear stress is tallow = 125 psi.
Determine the largest shear force V that the member can sustain if the allowable shear stress is tallow = 8 ksi.
If a = 3 in. and the wood has an allowable normal stress of sallow = 1.5 ksi, and an allowable shear stress of tallow = 150 psi, determine the maximum allowable value of P that can act on the beam.
The beam is subjected to a shear of V=39 kN V=39 kN. Set w=200 mm w=200 mm Part A Determine the web's shear stress at A. Part B Determine the web's shear stress at B.
The beam is constructed from two boards fastened together at the top and bottom with three rows of nails spaced every 8 in. If an internal shear force of V = 800 lb is applied to the boards, determine the shear force resisted by each nail.
Determinea) the maximum shear stress, along the beam,b) the maximum tensile bending stress along thebeam,c) the maximum compressive bending stress alongthe beam.d) If the top board (20 mm x 60 mm) is connectedwith the nails to the below part, determine themaximum allowable spacing s, if each nail canresist a shear force of 1.5 kN.
If the shaft is made from a material having an allowable shear stress of τallow = 95 MPa , determine the maximum value for P.
The double T-beam is fabricated by welding the three plates together as shown. If the weld can resist a shear stress tallow = 90 MPa, determine the maximum shear V that can be applied to the beam.