A. Using Euler formula, determine if the column fails by elastic or inelasticbuckling if a W10x22 (A= 6.49 in2, Ix= 118in4, rx= 4.27 in, Iy=l1.4in4 andry= 1.33in) is used as a 15ft long pin-connected column, assuming the steelhas a proportional limit of 36 ksi.B. Repeat part (a) if the length of the column is changed to 8 ft.

Answered: Image /qna-images/answer/e3d31bf6-480d-4225-90fe-f6b2024d903a.jpg

A. Using Euler formula, determine if the column fails by elastic or inelastic buckling if a W10x22 (A= 6.49 in2, Ix= 118in4, rx= 4.27 in, Iy=11.4in4 and ry= 1.33in) is used as a 15ft long pin-connected column, assuming the steel has a proportional limit of 36 ksi. B. Repeat part (a) if the length of the column is changed to 8 ft.

A. Using Euler formula, determine if the column fails by elastic or inelastic buckling if a W10x22 (A= 6.49 in2, Ix= 118in4, rx= 4.27 in, Iy=11.4in4 and ry= 1.33in) is used as a 15ft long pin-connected column, assuming the steel has a proportional limit of 36 ksi. B. Repeat part (a) if the length of the column is changed to 8 ft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.1P: A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness...

See similar textbooks

Similar questions

A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness ßRat A. Determine the critical load Pcr for the structure.
Select a steel wide-flange column of a nominal depth of 360 mm (W 360 shape) to support an axial load P = 1100 kN (see figure). The column has pinned ends and length L = 6 m. Assume E = 200 GPa and y= 340 MPa. Note: The selection of columns is limited to those listed in Table F-l(b), Appendix F.
A steel column (E = 200 GPa) is 9 m long, embedded in aone end and supported on the other. If the section is shown below, determine if it would break by loss.of stability, where ?? = 250 ???.
(i) A homogeneous prismatic bar hangs from a ceiling verticallydownwards under its own weight. The bar has density,?,Length, L and cross-sectional area, A. Show that the total elongation of the bar is given by Eq. (1):
A 75 mm diameter compound bar is constructed by shrinking a circularbrass bush onto the outside of a 45 mm diameter solid steel rod. If thecompound bar is then subjected to an axial compressive load of 170 kN,determine the load carried by the steel rod. The modulus of elasticity for steel,Es = 200 GN/m2 , and brass, Eb = 100 GN/m2
Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and made of aluminum that has anelastic modulus of E = 12,000 ksi. Determine the maximum magnitude of load P that can be applied to the rigid bar withoutcausing member (1) to buckle
Determine the critical axial buckling load for an 8 3/4 x 12 inches glue-laminated column braced at 10ft from the bottom in the y axis for a total height of 25ft. Assume pin connections at top and bottom. Fc= 1750 psi, E= 1.8x106 psi. (Western cross-section glu-lam data is in the text).
A wide flange A60 steel column has a length of 4.5meters and pinned ends. If Sx=898x103 mm3, Sy=120x103 mm3, d=358mm, bf=171mm, A=7,159mm2, Fy=414MPa, calculate the design compressive strength in KN of the column. Express your answer in one decimal place.
The rigid bar AB with a length of 5m, is attached to two vertical rods and ishorizontal before the uniformly varying load of zero intensity at point A and 10kN/mat point B is applied. The rod at A is steel with L=3m, A=300 mm2 and E=200GPa. Therod in B is aluminum with L=4m, A=500mm2 and E = 70GPa. Determine the verticaldisplacement of the bar at a point where the resultant of the load is acting.
A hollow steel [E= 30,000 ksi] tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum [E= 10,000 ksi] rod (2) that has a 2-in.-diameter and a solid 1.375-in.-diameter aluminum rod (3). Determine: (a) the change in length of steel tube (1).(b) the deflection of joint D with respect to the fixed support at A.(c) the maximum normal stress in the entire axial assembly.
A hollow circular column of 200 mm external and 160 mm internal diameter is subject to anaxial compressive load of 150 kN with an eccentricity of 25 mm from the centroidal axis.The column is 5.0 m long and both ends fixed. Determine the maximum compressive stressand deflection in the column (assume E = 120 GPa).
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4350 mm2 and an allowable normal stress of 130 MPa. Bar (2) has a cross-sectional area of A2 = 4550 mm2 and an allowable normal stress of 80 MPa. Assume x1 = 2.2 m, x2 = 2.9 m, y1 = 1.3 m, and y2 = 2.6 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.