Acetylene torches are used for welding. These torches use a mixture of acetylene gas, C2H2, and oxygen gas, O2 to produce the following combustion reaction: 2 C2H2 (g) + 5 O2 (g) →4 CO2 (g) + 2 H20 (g) Imagine that you have a 5.6 L gas tank and a 2.3 L gas tank. You need to fill one tank with oxygen and the other with acetylene to use in conjunction with your welding torch. If you fill the larger tank with oxygen to a pressure of 113 atm, to what pressure should you fill the acetylene tank to ensure that you run out of each gas at the same time? Assume ideal behavior for all gases. Express your answer numerically, in terms of atm to 0 decimal places.

Acetylene torches are used for welding. These torches use a mixture of acetylene gas, C2H2, and oxygen gas, O2 to produce the following combustion reaction: 2 C2H2 (g) + 5 O2 (g) →4 CO2 (g) + 2 H20 (g) Imagine that you have a 5.6 L gas tank and a 2.3 L gas tank. You need to fill one tank with oxygen and the other with acetylene to use in conjunction with your welding torch. If you fill the larger tank with oxygen to a pressure of 113 atm, to what pressure should you fill the acetylene tank to ensure that you run out of each gas at the same time? Assume ideal behavior for all gases. Express your answer numerically, in terms of atm to 0 decimal places.

Chemistry for Engineering Students

4th Edition

ISBN:9781337398909

Author:Lawrence S. Brown, Tom Holme

Publisher:Lawrence S. Brown, Tom Holme

Chapter5: Gases

Section: Chapter Questions

Problem 5.93PAE: 93 The complete combustion of octane can be used as a model for the burning of gasoline:...

See similar textbooks

Similar questions

You have a 550.-mL tank of gas with a pressure of 1.56 atm at 24 C. You thought the gas was pure carbon monoxide gas, CO, but you later found it was contaminated by small quantities of gaseous CO2 and O2. Analysis shows that the tank pressure is 1.34 atm (at 24 C) if the CO2 is removed. Another experiment shows that 0.0870 g of O2 can be removed chemically. What are the masses of CO and CO2 in the tank, and what is the partial pressure of each of the three gases at 25 C?
97 Homes in rural areas where natural gas service is not available often rely on propane to fuel kitchen ranges. The propane is stored as a liquid, and the gas to be burned is produced as the liquid evaporates. Suppose an architect has hired you to consult on the choice of a propane tank for such a new home. The propane gas consumed in 1.0 hour by a typical range burner at high power would occupy roughly 165 L at 25°C and 1.0 atm, and the range chosen by the client will have six burners. If the tank under consideration holds 500.0 gallons of liquid propane, what is the minimum number of hours it would take for the range to consume an entire tankful of propane? The density of liquid propane is 0.5077 kg/L.
93 The complete combustion of octane can be used as a model for the burning of gasoline: 2C8H18+25O216CO2+18H2O Assuming that this equation provides a reasonable model of the actual combustion process, what volume of air at 1.0 atm and 25°C must be taken into an engine to burn 1 gallon of gasoline? (The partial pressure of oxygen in air is 0.21 atm and the density of liquid octane is 0.70 g/mL.)
94 Mining engineers often have to deal with gases when planning for the excavation of coal. Some of these gases, including methane, can be captured and used as fuel to support the mining operation. For a particular mine, 2.4 g of CH4 is present for every 100.0 g of coal that is extracted. If 45.6% of the methane can be captured and the daily production of the mine is 580 metric tons of coal, how many moles of methane could be obtained per day?
You have a gas, one of the three known phosphorus-fluorine compounds (PF3, PF3, and P2F4). To find out which, you have decided to measure its molar mass. (a) First, yon determine that the density of the gas is 5.60 g/L at a pressure of 0.971 atm and a temperature of 18.2 C. Calculate the molar mass and identify the compound. (b) To check the results from part (a), you decide to measure the molar mass based on the relative rales of effusion of the unknown gas and CO2. You find that CO2 effuses at a rate of 0.050 mol/min, whereas the unknown phosphorus fluoride effuses at a rate of 0.028 mol/min. Calculate the molar mass of the unknown gas based on these results.
105 The decomposition of mercury(II) thiocyanate produces an odd brown snake-like mass that is so unusual the process was once used in fireworks displays. There are actually several reactions that take place when the solid Hg(SCN)2 is ignited: 2Hg(SCN)2(s)2HgS(s)+CS2(s)+C3N4(s)CS2(s)+3O2(g)CO2(g)+2SO2(g)2C3N4(s)3(CN)2(g)+N2(g)HgS(s)+O2(g)Hg(l)+SO2(g) A 42.4-g sample of Hg(SCN)2 is placed into a 2.4-L vessel at 21°C. The vessel also contains air at a pressure of 758 torr. The container is sealed and the mixture is ignited, causing the reaction sequence above to occur. Once the reaction is complete, the container is cooled back to the original temperature of 21°C. (a) Without doing numerical calculations, predict whether the final pressure in the vessel will be greater than, less than, or equal to the initial pressure. Explain your answer. (b) Calculate the final pressure and compare your result with your prediction. (Assume that the mole fraction of O2 in air is 0.21.)
A mixture contained zinc sulfide, ZnS, and lead sulfide, PbS. A sample of the mixture weighing 6.12 g was reacted with an excess of hydrochloric acid. The reactions are ZnS(s)+2HCL(aq)ZnCl2(aq)+H2S(g)PbS(s)+2HCL(aq)PbCl2(aq)+H2S(g) If the sample reacted completely and produced 1.049 L of hydrogen sulfide, H2S, at 23C and 762 mmHg, what were the percentages of ZnS and PbS in the mixture?
Methanol (CH3OH) can be produced by the following reaction: CO(g)+2H2(g)CH3OH(g) Hydrogen at STP flows into a reactor at a rate of 16.0 L/min. Carbon monoxide at STP flows into the reactor at a rate of 25.0 L/min. If 5.30 g methanol is produced per minute, what is the percent yield of the reaction?