acting on a very small member are shown in the figure. a) The greatest shear stress theory b) Find the coefficients of safety for flow, taking into account the theory of maximum strain

Q: Given data: Maximum shear stress-50 MPa Maximum principal stress=80 MPa Find minimum principal…

A:

Q: Q2 Figure Q2 shows few loadings applied on bar ABD. Suppose the diameter of the bar is A mm, and…

A: According to the figure showing P1, P2 are forces, but according to the given units, it is moment. I…

Q: Oox= 10 MPa (compres Q2 (a): Figure below shows the state of stress at a critical point on a…

A: Givenσxx=10MPaσyy=25 MPaτxy=90 MPaσzz=20 MPaSyt=300 MPaSyc=600 MPaSsy=200 MPaεF=0.15

Q: The state of stress in a material is given in the figure. Maximum principal stress will be 45 45 5 5…

A: Given, Tensile stress in x-direction = σx = 5 units Tensile stress in y-direction = σy = 5 units…

Q: A 10 mm diameter rivet holds three sheets of metal together and is loaded as shown in figure below,…

A:

Q: The articular Cartilage is subjected to plane stress with normal stresses og , Oy and shear stress…

A:

Q: At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress…

A: Given:σx=-30 MPaσy=15 MPaζxy=25 MPaθ=-25°

Q: Q2) Layers of Brass, Steel and Aluminum are bonded together and formed section shown below.…

A:

Q: Q2 A solid circular bar ABC consists of two segments, as shown in figure 2. One segment has diameter…

A: The diameter of the shaft can be determined by two criteria 1) Shear stress 2) Angle of twist Both…

Q: A rod subjected tensile stress is 15.92 x 10°N/mm2 and tensile strain is 0.01 then find young…

A:

Q: In the below figure, if the shear stress on the bolt shown in the first figure is 60 MN/m2. The…

A: Consider the shear force diagram for the first figure,

Q: ed shear stress. Given: a = 1 mm, b = 100 mm and G = 25 GPa. Consider a linear elastic behavior.…

A: given:a=1mmb=100mmG=25Gpa

Q: you! A round vertical steel tank has an inside diameter of 3 m and is 6.5 m in height. It contains…

A: Given:d=3 mh=6.5 mρ=850 Kg/m3σallow=25 MPa

Q: Ql: For the Figure shown below, determine (a) the principal stresses and show them on a sketch of a…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A:

Q: Q2 Figure Q2 shows few loadings applied on bar ABD. Suppose the diameter of the bar is A mm, and…

A:

Q: Estimate the normal stress (on) and shear stress (t) on the inclined plane as shown in the below…

A:

Q: The principal stresses at a point are 70, 60 and -18 MPa; say o, is the yield point stress of the…

A: Given data

Q: Using the Mohr circle or analytical solution for the plane stress case in the figure; (a) Principal…

A:

Q: The stress at a point of a machine component are 200MPa tensile and 100MPa compressive. Using Mohr’s…

A: Given: σx=200 MPaσy=-100 MPaτxy=0θ=30°

Q: Home Work 2 The articular Cartilage is subjected to plane stress ith normal stresses ox, Oy and…

A: Write the expression of the normal stress developed on an oblique surface when θ = 30°.

Q: The shaft of a mechanical device is designed to transmit the torque T = 100 N. m. The shaft could be…

A:

Q: Determine the maximum shear force in kN in the figure below. 30 kN 140 kN • m A D В C +2 m- 3 m 2 m→

A:

Q: The stress- strain curve for four materials are shown in figure below. Which material (A/B/C/D) has…

A:

Q: A cylinder has an ID of 100 mm and an internal pressure of 50 MPa. Find the needed wall thickness if…

A: Given data:           cylinder     Internal diameter=Di =100mm     Internal pressure=Pi…

Q: 3) Use the diagram below to answer the following questions. 18 ksi 4 ksi 6 ksi A) What are the…

A: Given The value of normal stress is σx=6 ksi and σy=8 ksi. The value of shear stress is τxy=4 ksi.…

Q: A journal bearing has 8 cm diameter and length to diameter ratio of 3. Find the projected area in…

A:

Q: Given a stress element in the figure, find the planes in which the normal stresses are equal in…

A:

Q: details are given, rivets and plates. Find the maximum shear, crush and tear (tensile) stresses.…

A:

Q: Q2) In Figure show the force- extension curve for three materials. a) Material b) Material c)…

A: Yield strength: It is the maximum stress which can be developed in a material without causing any…

Q: The principal stresses at a point in a solid are o,=56Mpa, o,=35Mpa, and o3=14Mpa. Using Mohr's…

A:

Q: The pole in Figure  is at a 90.0∘ bend in a power line and is therefore subjected to more shear…

A: Given that , Tension ,T =5 ×104Nh=15 m d=16×10-2m

Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…

A:

Q: Q2) In Figure show the force- extension curve for three materials. a) Material b) Material c)…

A: Given Force elongation graph To find High ductility material High ultimate strength Brittle material…

Q: て。 しx 6*

A:

Q: At a point in a material, the principal stresses are 800 N/cm² and 300 N/cm² where both are tensile.…

A:

Q: A В 3 m Figure Q3(a)

A: (a) To plot the stress strain diagram for elastic-perfectly plastic material. (b) To find P = ?

Q: The drive shaft for a truck (outer diameter 80 mm and inner diameter 25 mm) is running at 2,300 rpm…

A:

Q: Format TL GyabGSkin -a-0630b/a) 60 MPa 45 MPa My 100 MPа 100MPA w-, cos20 + tysin20, oun =% * °%,…

A: Given Data The stress acting in x direction is: σx=100 MPa. The stress acting in y direction is:…

Q: An element in plane stress is subjected to stresses: o, = 85 MPa, o, = -30 MPa, and y = 32MPA, as…

A:

Q: Q4: For the figure below, determine the principal stresses and show them on a sketch of a properly…

A: Normal stress is defined as the intensity of force exerted over a unit cross sectional area which…

Q: Determine the maximum shear force in kN in the figure below. 2 kN/m B C A 4 m 2 m 5 kN

A:

Q: For a plane stress state, in the original Oxy system we know the component o = 120 MPa and try = 60…

A: Given data:-σx=120MPa, τxy=60MPa, τx'y'=-60MPa, θ=45°(in CCW direction)There is a general expression…

Q: P2.12 (WP A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q…

A:

Q: Consider the following plane stress state: Ox= -4 MPa, oy 12 MPa, Txy=7 MPa ccw Calculate the…

A: Calculated the centre coordinate of the mohr circle. and calculated principal stress and maximum…

Q: 1. For the two cases i.e. (a) 2D and (b) 3D shown below, find the principal stresses, maximum shear…

A: a) The given values are - σx= 60MPa , τxy=40 MPa , σy= 0 The principal stresses are given by - σ1,…

Q: The stress-strain curve for four materials are shown in figure below. Which material (A/B/C/D) has с…

A: Answers are as follows: 1. Material D (Least slope of a straight line in the stress-strain diagram)…

Q: A solid aluminum bar (G = 27 GPa) of diameter d= 60 mm is subjected to torques T= 280 N - m acting…

A:

Q: A circular steel shaft with length, L (m) has an outer diameter, d2 (mm) and inner diameter, d1…

A: