Activity 1. The frame shown is hinged to rigid supports at A and B. Find the horizontal andvertical components of the forces at A and E, and the forces in members BC and BD.(Ans. EH=2500N, Av=400N, BD=4166.67N(C), BC=2833.33N(T)300N600N2mB2m2m1.2mEF5.1m0.90m

The support reactions at points A and E can be determined by using the 3 static equations as:…

Answered: Activity 1. The frame shown is hinged…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A frame structure, as shown in the following diagram, is given. Calculate: (a) Reaction forces at each support (b) Forces acting on members AB, BD, and DE using the Section Method And it is known that P = 700 kN, Q = 300 kN, a = 10 m, b = 8 m, and c = 6m
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N Which option is right? a) if the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position or b) if the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position
A steel plate of dimensions 2.5 x 1.5 x 0.08 m and weighing 23.1 kN is hoisted by steel cables with lengths L1 = 3.2 m and L2 = 3.9 m that are each attached to the plate by a clevis and pin (see figure). The pins through the clevises are 18 mm in diameter and are located 2.0 m apart. The orientation angles are measured to be s = 94.4' and a = 54.9° For these conditions, first determine the cable forces T1 and T2, then find the average shear stress Taver in both pin 1 and pin 2, and then the average bearing stress ?? between the steel plate and each pin. Ignore the weight of the cables.
Determine the internal forces at point D of the frame shown in the figure.
A two members truss ABC is shown in the figure. Determine the force transmitted in member AB
Activity 3. From a bar subjected by an axial force P, Draw the components of P acting on the inclined plane.
The rigid bar ABC is suspended from three wires of the same material. The cross-sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P.
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure, choose the alternatives that are true. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N If the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position. True or false?
Analyze the Structure given in Figure (Picture Attached) and determine the forces in each member of truss by Methods of Sections. State whether members are in tension or compression. P1= 720KN P2= 360KN
SITUATION 7: Three forces P1, P2, and P3 are acting on a semi-circular structure as shown in Fig. THA-33. Support at A is hinge and support at B is roller. Given: a = 1 m; P1 = 1.8 kN; P2 = 0.9 kN; P3 = 0.45 kN; θ = 30⁰; β = 45⁰. Calculate the resultant of the three forces (in kN). (Answer: 2.45) Calculate the vertical reaction at B (kN). (Answer: 1.06) Calculate the reaction at A. (Answer: 1.63)
A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0,respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the leftend where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) andthe weight (W) of the bar
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN. Angle α = 31 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Activity 1. The frame shown is hinged to rigid supports at A and B. Find the horizontal and vertical components of the forces at A and E, and the forces in members BC and BD. (Ans. EH=2500N, Av=400N, BD=4166.67N(C), BC=2833.33N(T) 300N 600N A 2m в 2m c. 2m D 1.2m F 5.1m 0.90m