The simple truss is loaded by a system of forces as shown in the figure. The truss is supported by a pin at A and a roller at E. If P1 = 40 [KN] and P2 = 20 [KN], then the force developed in the member (EF) is. 4个 B 2 m E -1.5 m-1.5 m1.5 m-1.5 m-| P1 P2 Select one: a. 18.75 kN - Tension b. 78.15 kN - Compression

The simple truss is loaded by a system of forces as shown in the figure. The truss is supported by a pin at A and a roller at E. If P1 = 40 [KN] and P2 = 20 [KN], then the force developed in the member (EF) is. 4个 B 2 m E -1.5 m-1.5 m1.5 m-1.5 m-| P1 P2 Select one: a. 18.75 kN - Tension b. 78.15 kN - Compression

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The mechanism shown in the figure controls the lifter. Calculate the reactions on CDE as the weight supported by the platform is W W(N)= 2800, L1(m)=0.6, L2(m)=0.6 , L3(m)=0.2 1) For three dimensional problems, please use vector notation.2) State what all the transactions you have done. All intermediate actions you have to doshow clearly.3) Please write the units next to the values you find.4) In the related questions, please draw the free body diagram.
The blood pressure in your heart is 1.52 x104 Pa. If an artery in the brain is 0.421 m above the heart, what is the pressure in the artery?
A) Imagine a procedure used for the execution of a certain work, as shown in the following figure. Such a crane has a mass of 1000 kg and is transporting a coffin with a total mass of 2400 kg. Assume that support A is fixed, support B is movable, and point G is the center of gravity of the lift. What are the support responses in kN? Question 1 options: a) The support responses are as follows: Rax = Rbx = 34 kN and Ray = 109.33 kN. b) The supporting responses are as follows: Rax = Ray = 109.33 kN and Rbx = 34 kN. c) The support responses are as follows: Rax = 56.8 kN; Rbx = 109.33 kN and Radius = 34 kN. d) The support responses are as follows: Rax = 156.7 kN; Rbx = 89.65 kN and Radius = 34 kN. e) The supporting responses are as follows: Rax = Rbx = 109.33 kN and Ray = 34 kN. B. Consider the beam shown in the following figure. In this beam, there are different types of existing forces, such as applied moment, distributed load and point load. Knowing the magnitude of each of the forces,…
The surface tensions of mercury and water at 60 degrees Celcius are 0.47N/m and 0.0662 N/m, respectively. What capillary height changes will occur in these two fluids when they are in contact with air in a glass tube of radius 0.30mm? Use θ = 130° for mercury, and 0° for water; y = 132.3 kN/m3 for mercury and 9.650 kN/m3 for water. Provide the given along with its solution. (Please write legibly, I did not understand the first solution.)
The height h to which a column of liquid will rise in a small-bore tube due to surface tension is a function of the density of the liquid ρ, the radius of the tube r, the acceleration due to gravity g, and the surface tension of the liquid σ (see Section 1.9.3). (a) Express this dependence in nondimensional terms. (b) If the capillary rise for liquid A is 25 mm in a tube of radius 0.5 mm, what will be the rise for a liquid B having the same surface tension but four times the density of liquid A in a tube of radius 0.25 mm a dynamically similar system? Also find rB.
what's mean below sentence? i couldn't understand θm=θ1-θ2lnθ1θ2=Thi-Tco-Tho-TcilnThi-TcoTho-Tci=60-55-30-20ln60-5530-20=7.2135 °C
The stress state within the lateral wall of a soda can is approximated as shown. p is the internal pressure, r is the radius of the can, t is the wall thickness. Express the stress state shown in a matrix, where the only two non-zero stress components are σxx and σyy, all other stress compoenents are zero. Express the equivalent stress σe associated with the stress state shown in terms of p, r, and t.
Generalize Prob. as follows. Denote length AB asH , length BC as L , and angle ABC as θ . Let the dam materialhave specifi c gravity SG. The width of the dam is b .Assume no seepage of water under the dam. Find an analyticrelation between SG and the critical angle θ c for whichthe dam will just tip over to the right. Use your relation tocompute θ c for the special case SG = 2.4 (concrete).
The load on a 2-in.-diameter hydraulic cylinder increases from 10,000 lb to 15,000 lb. Due to the compressibility of the oil, the piston retracts 0.1 in. If the volume of oil under compression is 10 in^3, what is the bulk modulus of the oil in units of kpsi? Enter only a whole number.
An infinite length plate on points A, B, C and D respectively Parallel forces FA, FB, FC and FD (kN) It acts in the directions given in the figure.point A is blue, point B is white, point C yellow, point D is on the green area. Given in the data table Equivalent composition using values the magnitude of the force (FEŞ) and find the application the x and y (m) coordinates of the point. (FA(kN)=24,FB(kN)=46,FC(kN)=24,FD(kN)=32) x and y (m) coordinates (XA=-19,YA=-7,XB=15,YB=-9,XC=20,YC=2,XD=-13,YD=8)
In the arrangement shown in the figure, a cable is attached to the end of a cantilever beam. We will model the cable as a rod. Denote the translational spring constant of the beam by kb and the translational spring constant of the cable by kc. The displacement x is caused by the applied force f. What is the equivalent spring constant for this arrangement?
During a bicep curl on a bicep curl machine, I'm curling a weight stack of 100 pounds (single arm...I'm jacked like that). At this very moment, the weight stack has a moment arm of 0.12m, my elbow has an angle of 63deg, my muscle force vector has an angle of 23deg, and it attaches 3cm below my elbow joint on my radius. How much force must my bicep create right at this moment to hold the weight stack in place?