www Aluminum 10K 12' w w Steel A 12' long beam in supported by an aluminum hanger at A and by a steel hanger at B. The beam carries a single 10K concentrated load. Neglect the self-weight of the beam. Both hangers have the same original length. Ealum = 10,000,000 psi Esteel = 29,000,000 psi If the load is located at midspan, and the steel hanger is a 1/2" x 1/2" bar, what is the width of the 1/2" aluminum bar, such that points A and B lie on the same horizontal line?

www Aluminum 10K 12' w w Steel A 12' long beam in supported by an aluminum hanger at A and by a steel hanger at B. The beam carries a single 10K concentrated load. Neglect the self-weight of the beam. Both hangers have the same original length. Ealum = 10,000,000 psi Esteel = 29,000,000 psi If the load is located at midspan, and the steel hanger is a 1/2" x 1/2" bar, what is the width of the 1/2" aluminum bar, such that points A and B lie on the same horizontal line?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.25P: An S6 × 12.5 steel cantilever beam AB is supported by a steel tic rod at B as shown. The tie rod is...

See similar textbooks

Similar questions

An aluminum bar having a rectangular cross section (2.0 in. × 1.0 in.) and length L = 30 in. is compressed by axial loads that have a resultant P = 2800 lb acting at the midpoint of the long side of the cross section (sec figure). Assuming that the modulus of elasticity E is equal to 10 × 106 psi and that the ends of the bar are pinned, calculate the maximum deflection and the maximum bending moment Mmax.
A fixed-end b earn is subjected to a point load at mid-span. The beam has a rectangular cross section (assume that the h/b ratio is 2) and is made of wood (E = 11GPa). Find height h of the cross section if the maximum displacement of the beam is 2 mm. Calculate the displacement of the beam at the inflection points.
Determine the allowable axial load Pallowa W 10 X 45 steel wide-flange column with pinned ends (see figure) for each of the following lengths: L = 8 ft, 16 ft, 24 ft, and 32 ft. (Assume E = 29,000 ksi and y = 36 ksi.)
Determine the allowable axial load Pallowfor a W 310 × 129 steel wide-flange column with pinned ends (see figure) for each of the following lengths: L = 3 m, 6 m, 9 m, and 12 m. (Assume E = 200 GPa and ( y= 340 MPa.)
A W8 × 28 steel wide-flange column with pinned ends carries an axial load P. What is the maximum permissible length of the column if (a) P = 50 kips, and (b) P = 100 kips? (Assume E = 29,000 ksi and y = 36 ksi.)
A propped cantilever steel beam is constructed from a W12 × 35 section. The beam is loaded by its self-weight with intensity q. The length of the beam is 1L5 ft. Let E = 30,000 ksi. Calculate the reactions at joints A and B. Find the location of zero moment within span AB. Calculate the maximum deflection of the beam and the rotation at joint B.
Solve the preceding problem for an aluminum column with b = 6,0 in., t = 0.5 in., P = 10 kips, and E = 10.6 × 106 ksi. The defied ion at the top is limited to 2.0 in.
An S6 × 12.5 steel cantilever beam AB is supported by a steel tic rod at B as shown. The tie rod is just taut when a roller support is added at Cat a distance s to the left of £, then the distributed load q is applied to beam segment AC, Assume E = 30 × 106 psi and neglect the self-weight of the beam and tie rod. Sec Table F-2(a) in Appendix F for the properties of the S-shape beam. (a) What value of uniform load q will, if exceeded, result in buckling of the tie rod if L1, =6 ft, s = 2 ft, H = 3 ft, and d = 0.25 in.? (b) What minimum beam moment of inertia ibis required to prevent buckling of the tie rod if q = 200 lb/ft, L1, = 6 ft, H = 3 ft, d = 0.25 in., and s = 2 ft? (c) For what distance s will the tic rod be just on the verge of buckling if q = 200 lb/ft, L1= 6 ft, M = 3 ft, and d = 0.25 in.?
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
An object of weight Wis dropped onto the midpoint of a simple beam AB from a height h (see figure). The beam has a rectangular cross section of area A. Assuming that h is very large compared to the deflection of the beam when the weight PFis applied statically, obtain a formula for the maximum bending stress crniilx in the beam due to the falling weight.
A pinned-end column with a length L = 18 ft is constructed from a W12 x 87 wide-flange shape (sec figure). The column is subjected to a centrally applied load P1=180 kips and an eccentrically applied load P2=15 kips. The load P2acts at a distance s = 5.0 in. from the centroid of the cross section. The properties of the steel arc E = 29,000 ksi and y = 36 ksi. Calculate the maximum compressive stress in the column. Determine the factor of safety with respect to yielding.
A wood column with, a rectangular cross section (see figure) is constructed of 4 in. × 8 im construction grade, western hemlock: lumber (Fc = 1000 psi, E = 1,300,000 psi). The net cross-sectional dimensions of the column arc b = 3.5 in. and h = 7.25 in. (see Appendix G). Determine the allowable axial load Pallow. for each of the following lengths: L = 6 ft, 8ft, and 10 ft.