Air enters a compressor operating at steady state with a pressure of 14.7 Ibf/in.? and atemperature of 70°F. The volumetric flow rate at the inlet is 16.6 ft'/s, and the flow area is0.26 ft'. At the exit, the pressure is 35 Ibf'in.?, the temperature is 280°F, and the velocity is50 fu's. Heat transfer from the compressor to its surroundings is 1.0 Btu per Ib of air flowing.Potential energy effects are negligible, and the ideal gas model can be assumed for the air.Determine the compressor power, in Btu/s and hp. Ans. W = -63.9 Btu/s and -90.38 hp

Given: The pressure of air at the inlet of the compressor, P1 = 14.7 lbf/in2 The temperature of air…

Air enters a compressor operating at steady state with a pressure of 14.7 Ibfin. and a temperature of 70°F. The volumetric flow rate at the inlet is 16.6 ft’/s, and the flow area is 0.26 ft°. At the exit, the pressure is 35 Ibfin.², the temperature is 280°F, and the velocity is 50 ft/s. Hcat transfer from the compressor to its surroundings is 1.0 Btu per Ib of air flowing. Potential energy effects are negligible, and the ideal gas model can be assumed for the air. Determine the compressor power, in Btu/s and hp. Ans. W =-63.9 Btw/s and -90.38 hp %3D

Air enters a compressor operating at steady state with a pressure of 14.7 Ibfin. and a temperature of 70°F. The volumetric flow rate at the inlet is 16.6 ft’/s, and the flow area is 0.26 ft°. At the exit, the pressure is 35 Ibfin.², the temperature is 280°F, and the velocity is 50 ft/s. Hcat transfer from the compressor to its surroundings is 1.0 Btu per Ib of air flowing. Potential energy effects are negligible, and the ideal gas model can be assumed for the air. Determine the compressor power, in Btu/s and hp. Ans. W =-63.9 Btw/s and -90.38 hp %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8Air enters the diffuser of a ramjet engine (schematic shown below) at 6 lbf/in.2, 420°R, with a velocity of 1800 ft/s, and decelerates essentially to zero velocity. After combustion, the gases reach a temperature of 2000°R before being discharged through the nozzle at 6 lbf/in.2 On the basis of an air-standard analysis, determine:(a) the pressure at the diffuser exit, in lbf/in.2(b) the velocity at the nozzle exit, in ft/s.Neglect kinetic energy except at the diffuser inlet and the nozzle exit. Assume combustion occurs at constant pressure and flow through the diffuser and nozzle is isentropic.
A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
Air enters the diffuser of a ramjet engine (schematic shown below) at 6 lbf/in.2, 420°R, with a velocity of 1600 ft/s, and decelerates essentially to zero velocity. After combustion, the gases reach a temperature of 2200°R before being discharged through the nozzle at 6 lbf/in.2 On the basis of an air-standard analysis, determine:(a) the pressure at the diffuser exit, in lbf/in.2(b) the velocity at the nozzle exit, in ft/s.Neglect kinetic energy except at the diffuser inlet and the nozzle exit. Assume combustion occurs at constant pressure and flow through the diffuser and nozzle is isentropic.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
Water flows through a horizontal coil heated by steam condenaing on the outside. If the inlet pressure and temperatire are 2 atm and 160°F (state 1) and at the exit 1 atm and 220 °F (state 2), calculate the heat added to the coil per pound mass of water. The entering velocity is 5 ft/s, and the leaving, 500 ft/s. Data: H1=127.9 Btu/lb, H2=1154.4 Btu/lbA. 1031 Btu/lbB. 1042 Btu/lbC. 1048 Btu/lbD. 1052 Btu/lb
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
Steam enters a turbine operating at steady state with a mass flow rate 1.28 kg/s. The power output of the turbine is 100kW. The inlet the enthalpy is given as 3177.2 KJ/kg. At the exit the pressure is 10 kPa and the quality is 90%. the change in kinetic energy between the inlet and outlet is negligible. calculate the heat transfer from the turbine to the surroundings
Water vapor is a stable working device with 30 bar pressure, 320°C temperature and 100 m/s speed. enters the nozzle. The outlet pressure and temperature are 10 bar and 200°C, respectively. Mass flow rate is 2 kg/s. Neglecting heat transfer and potential energy; a) Determine the ascent velocity in m/s. b) Determine the inlet and outlet flow areas in cm2.
Steam at 80 bar, 440 °C, enters aturbine operating at steady state with avolumetric flow rate of 236 m 3 /min.Twenty percent of the entering massflow exits through a diameter of 0.25m at 60 bar, 400 °C. The rest exitsthrough a diameter of 1.5 m with apressure of 0.7 bar and a quality of 90%. Determine the velocity at each exitduct, in m/s.
Air (??=7/2R constant)Cp=7/2R constant) expands in a steady‑state device from 874.8 kPa874.8 kPa and 701.4 K701.4 K to 329.2 K.329.2 K. If the process is adiabatic and reversible, what is the final pressure (in units of kPa)?
55 kmol per hour of air is compressed from P1 = 1 bar to P2 = 6.1 bar in a steady flow compressor. Delivered mechanical power is 98.9 kW. Temperatures and velocities are: T1 = 301K T2 = 520 K, u1 = 10.8 m/s and u2 = 3.8 m/s. Estimate the rate of heat transfer from the compressor in kW, 3 decimal values. Assume that Cp = 7/2R and that enthalpy is independent of pressure.
In the first stage of the impulse turbine, the adiabatic heat drop in the nozzle is 350 (kJ/kg), the velocity coefficient of the nozzle is 0.96, the nozzle exit angle is 20 degrees, the circumferential speed of the rotor is 350 m/s, the rotor The exit angle is 30 degrees. Find the next value.(1) Nozzle efficiency, (2) Draw a velocity triangle (scale), (3) Circumferential force acting on the rotor blade (4) Find the forward efficiency of the turbine.