Air is flowing in parallel over the upper surface of a flat plate with a length of 4m. The first half of the plate length, from the leading edge, has a constant surface temperature of 50 degrees Celsius. The second half of the plate length is subjected to a uniform heat flux of 86 W/m2. The air has a free stream velocity and temperature of 2 m/s and 10 degrees Celsius, respectively. Determine the local convection heat transfer coefficients at 1 m and 3 m from the leading edge. Evaluate the air properties at a film temperature of 30 degrees Celsius. Is the film temperature Tf=30 degrees Celsius applicable at x = 3 m?

Air is flowing in parallel over the upper surface of a flat plate with a length of 4m. The first half of the plate length, from the leading edge, has a constant surface temperature of 50 degrees Celsius. The second half of the plate length is subjected to a uniform heat flux of 86 W/m2. The air has a free stream velocity and temperature of 2 m/s and 10 degrees Celsius, respectively. Determine the local convection heat transfer coefficients at 1 m and 3 m from the leading edge. Evaluate the air properties at a film temperature of 30 degrees Celsius. Is the film temperature Tf=30 degrees Celsius applicable at x = 3 m?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.22P

See similar textbooks

Similar questions

Air is flowing in parallel over the upper surface of a flat plate with a length of 4 m. The first half of the plate length, from the leading edge, has a constant surface temperature of 50°C. The second half of the plate length is subjected to a uniform heat flux of 86 W/m2. The air has a free stream velocity and temperature of 0.5 m/s and 10°C respectively. The properties of air at Tf = 30°C are k = 0.02588 W/m∙K, ν = 1.608 × 10−5 m2/s, and Pr = 0.7282. Determine the local convection heat transfer coefficients at 1 m and 3 m from the leading edge.
Air is flowing in parallel over the upper surface of a flat plate with a length of 4 m. The first half of the plate length, from the leading edge, has a constant surface temperature of 50°C. The second half of the plate length is subjected to a uniform heat flux of 86 W/m2. The air has a free stream velocity and temperature of 0.5 m/s and 10°C respectively. The properties of air at Tf = 30°C are k = 0.02588 W/m∙K, ν = 1.608 × 10−5 m2/s, and Pr = 0.7282.Determine the local convection heat transfer coefficients at 1 m from the leading edge.
Air is flowing in parallel over the upper surface of aflat plate with a length of 4 m. The first half of the plate length,from the leading edge, has a constant surface temperatureof 50°C. The second half of the plate length is subjected toa uniform heat flux of 86 W/m2. The air has a free streamvelocity and temperature of 2 m/s and 10°C, respectively.Determine the local convection heat transfer coefficients at1 m and 3 m from the leading edge. Evaluate the air propertiesat a film temperature of 30°C. Is the film temperatureTf = 30°C applicable at x = 3 m?
During a cold winter day, wind at 55 km/h is blowing parallel to a 4m high and 10m long wall of a house. If the air outside is at 5 degrees Celsius and the surface temperature of the wall is 12 degrees Celsius , determine the rate of heat loss from the wall by convection. What would your answer be if the wind velocity has doubled? From Table A-1:thermal conductivity, k = 0.0246 W/m degrees Celsiusviscosity, v = 1.4 x 10^-5 m^2/sPrandtl no. Pr = 0.717
A long 8-cm-diameter steam pipe whose external surface temperature is 90°C passes through some open area that is not protected against the winds. Determine the rate of heat loss from the pipe per unit of its length when the air is at 1 atm pressure and 7°C and the wind is blowing across the pipe at a velocity of 50 km/h.
A long 10-cm-diameter steam pipe whose external surface temperature is 110°C passes through some open area that is not protected against the winds . Determine the rate of heat loss from the pipe per unit of its length when the air is at 1 atm pressure and 10°C and the wind is blowing across the pipe at a velocity of 8 m/s.
Air at 300 degrees Celsius flows over a plate of dimension 0.5 m by 0.25 m. If the convection heat transfer coefficient is 250 Watts per Sq.m Kelvin, determine the heat transfer rate from the air to one side of the plate if the plate is to be maintained at 40 degrees Celsius.
Question No. 3: During a cold winter day, wind at 55 km/h is blowing parallel to a 4-m-high and 10-m-long wall of a house. If the air outside is at 5°C and the surface temperature of the wall is12°C, determine the rate of heat loss from that wall by convection. What would your answer be if the wind velocity was doubled
Consider laminar flow of air across a hot circular cylinder. At what point on the cylinder will the heat transfer be highest? What would your answer be if the flow were turbulent?
What is natural convection? How does it differ from forced convection? What force causes natural convection currents?
Consider a 50-cm-diameter and 95-cm-long hot water tank. The tank is placed on the roof ofa house. The water inside the tank is heated to 80℃ by a flat-plate solar collector during theday. The tank is then exposed to windy air at 18℃ with an average velocity of 40 km/h duringthe night. Estimate the temperature of the tank after a 45-min period. Assume the tank surfaceto be at the same temperature as the water inside, and the heat transfer coefficient on the topand bottom surfaces to be the same as that on the side surface. Evaluate the air properties at50℃. (Answer: 69.9 ℃)
An average person generates heat at a rate of 84 W while resting. Assuming one-quarter of this heat is lost from the head and disregarding radiation, determine the average surface temperature of the head when it is not covered and is subjected to winds at 10°C and 25 km/h. The head can be approximated as a 30-cm-diameter sphere. Assume a surface temperature of 15°C for evaluation of ms. Is this a good assumption?