Al Fe Al Two aluminum rods (Eai = 10E6 psi) are held together by a fixed support on the left and a rigid cross-bar on the right. The left side of the bar (Efe = 28.5E6 psi) is attached to the fixed support, and there is a gap in b between the right end of the bar and the cross bar. The cross-sectional area of each rod is A = 0.5 in2 and the length is L = 10 in. The iron bar was stretched and welded by contacting the cross bar. After that, the axial strain of the iron bar was measured to obtain eFe=0.002. Find the size of gaр b. NEED STEP BY STEP AND DETAIL ANSWER BECAUSE I WANT TO LEARN

Al Fe Al Two aluminum rods (Eai = 10E6 psi) are held together by a fixed support on the left and a rigid cross-bar on the right. The left side of the bar (Efe = 28.5E6 psi) is attached to the fixed support, and there is a gap in b between the right end of the bar and the cross bar. The cross-sectional area of each rod is A = 0.5 in2 and the length is L = 10 in. The iron bar was stretched and welded by contacting the cross bar. After that, the axial strain of the iron bar was measured to obtain eFe=0.002. Find the size of gaр b. NEED STEP BY STEP AND DETAIL ANSWER BECAUSE I WANT TO LEARN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.11P: A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and...

See similar textbooks

Similar questions

A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
A wood-stave penstock of 1.8 m diameter is wrapped with steel hoops and subjected to a fluid pressure of 380 KPa. If the allowable tension in the hoop is 42.4 kN, what is the maximum hoop spacing?
The manhole cover of an ammonia storage tank is to be held by 25 stud bolts. If the pressure inside the storage tank will remain constant at 12.5 kg/cm2 and the manhole diameter is 508 mm, what should be the stress area of the carbon steel bolts?
A steel punch consists of two shafts: uppershaft and lower shaft. Assume that the upper shafthas a diameter d1 = 24 mm and the bottom shaft hasa diameter d2 =16 mm. The punch is used to inserta hole in a 4 mm plate, as shown in the figure. If aforce P = 70 kN is required to create the hole, whatis the average shear stress in the plate and the averagecompressive stress in the upper and lower shaft ofthe punch?
An axial pull of 40000 N is acting on a bar consisting of three sections of length 30 cm, 25 cm and 20 cm and of diameters 2 cm, 4 cm and 5 cm respectively. If the Young’s modulus = 2 × 105 N/mm2, determine : (i) stress in each section and (ii) total extension of the bar.
The gas tank consists of a cylindrical section with two hemispherical endcaps. The cylinder has a diameter of 75 cm and a wall thickness of 2 cm. If the allowable circumferential stress is 150 MPa and longitudinal stress is 100 MPa, find the maximum allowable internal pressure in the tank. Answer: P = ___________________
The tank shown in the figure is fabricated from 10 mm steel plate. Determine themaximum longitudinal and circumferential stress caused by an internal pressure of 1.2MPa.
The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. The thickness r,-r; is small compared to r; (a) Determine the axial force F in the ring in terms of p, w and r;. Hint: Consider a FBD by cutting the ring+membrane in two. (b) Determine the hoop stress in the ring. (c) Determine the hoop strain in the ring. The modulus of elasticity for the ring is E. (d) Relate the hoop strain to the change in the inner radius of the ring after this pressure is applied, and use this to get the change in the inner radius in terms of p, E, w, r, and ri- (PLEASE ANSWER ASAP AND CORRECTLY)!
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
please very urgent The bank in the figure is thought that a person is sittingthe force exerted on the board as 300 NIt is given. Elasticity of the boards that make up the benchmodule E = 7 GPa, the width of a board is 150 mm andSince the height is 30 mm, the person sitsCalculate the slump at the point. (Hint: ABas if built-in board A and BThink about it.) Dimensions ar in mm.
The tank shown in the figure is fabricated from 10 mm steel plate. determine the maximum longitudinal and circumferential stress caused by an internal pressure of 1.2 mpa