Q 5 A vertical axis circular cylindrical water storage tank of cross-sectional area A is filled to a depth of 15 m. The tank is 4 m in radius and is made of steel having a yield point of 240 MPa. If a safety factor of 2 is applied,determine the required tank wall thickness.. [Use ywater = 9800 N/m³]

Q 5 A vertical axis circular cylindrical water storage tank of cross-sectional area A is filled to a depth of 15 m. The tank is 4 m in radius and is made of steel having a yield point of 240 MPa. If a safety factor of 2 is applied,determine the required tank wall thickness.. [Use ywater = 9800 N/m³]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In designing a cylindrical pressure tank 1m in diameter, a factor of safety 2.5 is used. The cylinder is made of steel (oyield = 200MPa), and will contain pressure up to 7MPa. What is the required wall thickness based on circumferential stress condition?
A Horizontal Capillary Tube (Radius 10 Um) Con- Tains An Oil/Water Interface. The Pressure In The Oil Phase Is 14.5 Psi (100 KPa). Determine The Pressure In The Water Phase If The Contact Angle Is 30° And The IFT Is 30 Dynes/Cm (30 MN/M).
A thick-wall underwater pipe is placed at 20m below sea level. The pipe is carryingcompressed natural gas with pressure of 50 MPa. The pipe has 115mm outer diameter andmade of 316 stainless steel with yield strength of 205 MPa. The density of sea water could betaken as 1029 kg/m3. Find out:a) What is the resultant outer pressure acting on the underwater pipe? b) What is the minimum inner diameter to ensure the pipe does not yield?c) Sketch the variation of hoop and radial stress across the pipe wall, completed with stresslabelling. d) What is the resultant longitudinal stress of the pipe?
Please provide solutions. 1. A pipe 2.50 cm in diameter is 1.0 m long and filled with 0.60 m of water. If the pipe is capped at both ends and rotated in a horizontal plane about a vertical axis through one end of the pipe, what is the pressure at the other end of the pipe when it is rotating at 200 RPM? Problem A: An open vertical cylindrical tank 0.60 m in diameter and 1.20 m high is half full of water. If it is rotated about its vertical axis so that the water just reach the top, find the speed of rotation. What will then be the maximum pressure in the tank? If the water were 1.0 m deep, what speed will cause the water to just reach the top? What is the depth of the water at the center? 2. If the tank of Prob. A is half full of oil (sp. gr. 0.75) what speed of rotation is necessary to expose one-half of the bottom diameter? How much oil is lost in attaining this speed? Answer: 18.70 rad/s ; 42.5 litres
A vertical steel stand-pipe (a cylindrical tankopen at the top and having a vertical axis), is3m in inside diameter and 30 m high. The tankis filled with water having a weight density of104 N/m3. The material is structural steel havinga yield point of 270 MPa and a safety factor of2 is to be used. (a)What is the requiredthickness in terms of millimeters, of steel platenecessary at the bottom of the tank if thewelded longitudinal seam is presumed to be asstrong as the solid metal? (b) What wallthickness in terms of millimeters, is required ifthe seam is only 72% as strong as the solidmetal?
a cylindrical pressure vesssel( diameter =2.8m and wall thickness of 35mm) is made of steel. the maximum pressure inside the tank is 2.0Mpa. Based on the tresca( maximum shear stress criterion) what is the required yield stress of the steel. Show all work. I need an expert to solve it.
Answer: 57.4 ft/s=17.5m/sTorricelli's equation does not apply but the simplified Bernoulli's equation does apply.
A water pump is used to pump water from one large reservoir to another large reservoir that is at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure, as sketched in Fig. The dimensions and minor loss coefficients are provided in the figure. The pump’s performance is approximated by the expression Havailable = H0 − aV.2 , where shutoff head H0 = 24.4 m of water column, coefficient a = 0.0678 m/(Lpm)2 , available pump head Havailable is in units of meters of water column, and capacity V. is in units of liters per minute (Lpm). Estimate the capacity delivered by the pump. A
A continous wood stave pipe is 3.0 m in diameter and is in service under a head of 30.0 m of water. The staves are secured by means of round 25 mm steel hoops with allowable stress of 105 MPa. Find the masimum spacing in cm of the hoops to safely secure the pipe. Assume that there is an initial tension of 7000 N applied to the hoops.
A cylindrical vessel whose ends are closed by means of rigid flange plate is made of steel plate 3 mm thick. The length and internal diameter of vessel 500 mm and 25 cm respectively. The internal fluid pressure is 3 MN/m2. The value of the change in length is
Torricelli’s idealization of effl ux from a hole in the side ofa tank is V = √2 gh, as shown in Fig. P3.81. The cylindricaltank weighs 150 N when empty and contains water at20 °C. The tank bottom is on very smooth ice (static frictioncoeffi cient ζ ≈ 0.01). The hole diameter is 9 cm. For whatwater depth h will the tank just begin to move to the right?
End D of a 2.5 long uniformly plain wooden rod( s.g=0.7) is held 0.3m below the surface of still water. (a.) How much of the rod remains above the water surface? (b.) if the rod diameter is 25mm what force of D is required to hold it in place ?