An air-standard Otto cycle has a compression ratio of 7.6. The temperature is 650 K at the end of the expansion process and the heat rejection from the cycle is 270 kJ/kg of air. Use air-standard approach (DO NOT use constant specific heats) to calculate the temperature values at the end of compression (T2=) and heat addition (T3=) processes in K. A typical P-v diagram for a Otto cycle is shown for your reference. From the choices below, drag and drop the closest answers to the provided boxes in the question. (in Turkish- aşağıdaki seçeneklerden hesapladığınız yanıtlara en yakın olanını sürükleyip ilgili kutuya taşıyınız) PI

An air-standard Otto cycle has a compression ratio of 7.6. The temperature is 650 K at the end of the expansion process and the heat rejection from the cycle is 270 kJ/kg of air. Use air-standard approach (DO NOT use constant specific heats) to calculate the temperature values at the end of compression (T2=) and heat addition (T3=) processes in K. A typical P-v diagram for a Otto cycle is shown for your reference. From the choices below, drag and drop the closest answers to the provided boxes in the question. (in Turkish- aşağıdaki seçeneklerden hesapladığınız yanıtlara en yakın olanını sürükleyip ilgili kutuya taşıyınız) PI

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A petrol engine with compression ratio of 15:1 was analysed as an air-standard cycle. The inlet pressure and temperature of the air are 101 kPa and 15 0C respectively while the maximum temperature of the cycle is 1,344 0C. The mass flow rate of air through the engine is 615 kg/min when running at its optimum speed. Thake the specific heat capacites at constant pressure as 1.0038 and 0.714 kJ/kgK. Calculate the thermal efficiency of the cycle power obtainable from the cycle
An Otto cycle engine installed in a road vehicle has a volume compression ratio of 6 and provides a gas mileage of 15 mpg at the vehicle’s normal traveling speed of 40 mph. For purposes of this problem, the cycle can be assumed to be an ideal Otto cycle using air with fixed values of specific heats. The specific heat values are:
At the beginning of the compression process of an air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and mass flow rate in the system is 1900 kg/hr.cp = 1.006 kJ/kg K cv = 0.717 kJ/kg K calculate the thermal efficiency of the cycle in %? Answer to 1 decimal place.
The maximum temperature of a diesel engine operating on an air standard cycle is 1200K. If the engine's compression ratio is 20 and the air temperature at the entry condition is 300 degrees Celsius. Determine the cycle's efficiency.
The upper and lower temperature limits for an Otto cycle are 1500 K and 300 K respectively. What compression ratio is required to develop maximum work? Estimate the maximum theoretical power developed by an engine working on this cycle when the air flow rated is 0.35 kg/min.
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 1950 K. Determine the cutoff ratio. rc =
One kilogram of air was used as prime mover in a standard Otto cycle. The temperatures during the start and end of the compression stroke are 400K and 600K, respectively. Given that the displaced volume is 2m3 while the mean effective pressure is 40kPa. Determine the following. a. Heat Added b. Efficiency c. Pressure Ratio d. Compression Ratio e. Pressure at the start of the intake stroke
THERMODYNAMICS The compression ratio of an air-standard dual cycle is 14 and the cutoff ratio is 1.2. During the constant-volume heat addition process, the pressure ratio is 1.5. Determine the thermal efficiency, heat added, maximum gas pressure, and temperature when this cycle is run at 80 kPa and 20 degree celcius at the start of the compression. Make use of the cold-air assumption. Show complete solution on a paper.
The compression ratio of a 4-cylinder and 4-stroke Otto engine is 10, and the fluid circulating in the cycle is m = 0.002 kg / turn. At the beginning of the compression process, the air temperature is 290 K, the pressure is 100 kPa. The highest temperature of the cycle is 2000 K. Assuming that the engine works according to the ideal Otto cycle, calculate the number of revolutions (revolutions / minute) required to produce 100 kW of power. Cv = 0.7165 kJ / kg K.
Given problem: a.) Calculate the thermal efficiency of an air-standard Diesel cycle operating with a compression ratio of 23 and cutoff ratio of 2.25 b.) Determine the air-standard efficiency of an engine operating on the diesel cycle with a clearance of 8% and a cut-off ratio of 1.75. Assume k = 1.4.
At the beginning of the compression process of air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and the mass flow rate in the system is 1900 kg/hr. Cp=1.006 kJ/kg K Cv= 0.717 kJ/kg K 1) calculate the thermal efficiency of the cycle in %? 2) which formula should be used to determine the thermal efficiency of the cycle ?
5. (a) If the compression ratio of an engine working on Otto cycle isIncreased from 5 to 7, find the percentage increase in thermalefficiency. (b) Derive an expression for thermal efficiency of ideal Brayton cycle.(c) In an engine working on the ideal Otto cycle, the pressure and temperature at the beginning of compression are 100 kPa and 40 °C respectively. The ratio of specific heat capacities is 1.4. If the airstandard efficiency of the engine is 50%, determine(i) The compression ratio. (ii) The pressure and temperature at the end of adiabaticcompression. (6a) Explain and discuss in your own words, the following three concepts incombustion: stoichiometric mixture of air and fuel, weak mixture and richmixture. Explain their importance in combustion applications.(6b) A gas fuel has the following volumetric composition:Propane C3H8: 73 %Butane C4H10: 5 %Ethane, C2H6: 3%Nitrogen N2: 19%(i) Write out the complete combustion equations for all the combustible constituents individually.…