An aluminum alloy [E = 10,000 ksi; ay = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi; oy=45 ksi] pipe at flange B. The pipes are attached to rigid supports at A and C. Pipe (1) has an outside diameter of 2.425 in., a wall thickness of 0.21 in., and a length of L₁-8 ft. Pipe (2) has an outside diameter of 5.00 in., a wall thickness of 0.20 in., and a length of L₂ = 14 ft. If a minimum factor of safety of 2.1 is required for each pipe, determine: (a) the maximum load P that may be applied at flange B. (b) the deflection of flange B at the load determined in part (a). Deflection to the right is positive.

An aluminum alloy [E = 10,000 ksi; ay = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi; oy=45 ksi] pipe at flange B. The pipes are attached to rigid supports at A and C. Pipe (1) has an outside diameter of 2.425 in., a wall thickness of 0.21 in., and a length of L₁-8 ft. Pipe (2) has an outside diameter of 5.00 in., a wall thickness of 0.20 in., and a length of L₂ = 14 ft. If a minimum factor of safety of 2.1 is required for each pipe, determine: (a) the maximum load P that may be applied at flange B. (b) the deflection of flange B at the load determined in part (a). Deflection to the right is positive.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 0.5-in.-diameter steel [E= 30,000 ksi] bolt (1) is placed in a copper tube (2). The copper [E= 16,000 ksi] tube has an outside diameter of 1.00 in., a wall thickness of 0.125 in., and a length of L= 8.0 in. Rigid washers, each with a thickness of t= 0.125 in., cap the ends of the copper tube. The bolt has 20 threads per inch. This means that each time the nut is turned one complete revolution, the nut advances 0.05 in. (i.e., 1/20 in.). The nut is hand-tightened on the bolt until the bolt, nut, washers, and tube are just snug, meaning that all slack has been removed from the assembly but no stress has yet been induced. What stresses are produced in the bolt and in the tube if the nut is tightened an additional quarter turn past the snug-tight condition?
At a temperature of 60°F, a 0.03-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.70 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.9 in. and a thickness of 0.70 in. The supports at A and C are rigid. Assume h1=3.0 in., h2=1.9 in., L1=27 in., L2=47 in., and Δ=Δ= 0.03 in. Determine(a) the lowest temperature at which the two bars contact each other.(b) the normal stress in the two bars at a temperature of 260°F.(c) the normal strain in the two bars at 260°F.(d) the change in width of the aluminum bar at a temperature of 260°F.
At a temperature of 60°F, a 0.03-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.70 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.9 in. and a thickness of 0.70 in. The supports at A and C are rigid. Assume h1=3.0 in., h2=1.9 in., L1=27 in., L2=47 in., and Δ=Δ= 0.03 in. Determine:
Data:P = 2 kipd = 3.6 inchw = 305 millimeterst = 0.03 meterr = 5.08 centimeterh = 0.6667 feet a) Calculate the maximum static stress in the material (in MPa). b) Estimate the theoretical stress concentration factor at the fillet c) Estimate the theoretical stress concentration factor at the hole
At a temperature of 60°F, a 0.05-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 2.9 in. and a thickness of 0.80 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.9 in. and a thickness of 0.80 in. The supports at A and C are rigid. Assume h1=2.9 in., h2=1.9 in., L1=28 in., L2=42 in., and Δ=Δ= 0.05 in. Determine(a) the lowest temperature at which the two bars contact each other.(b) the normal stress in the two bars at a temperature of 255°F.(c) the normal strain in the two bars at 255°F.(d) the change in width of the aluminum bar at a temperature of 255°F. Determine the lowest temperature, Tcontact, at which the two bars contact each other.
A tensile load of 330,000 N is applied to a copper pipe with maximum allowable stress of 110 MPa and 80 mm inner diameter. What should be the thickness of the pipe? Choices: A. 9.78 mm B. 12.35 mm C. 11.56 mm D. 10.55 mm
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
given: - initial length of steel tube= 200mm - aluminum rod is 0.175 mm shorter than steel tube. - l=0.175 mm properties of materials - ALUMINUM: coefficient of linear expansion: 23x10-6 /C modulus of elasticitty= 70 GPa - STEEL Coeficient of linear expansion: 11x10-6 /C Modulus of elasticity: 200 GPa *NEGLECT SHEAR AND LATERAL DEFORMATIONS. REQUIRED: - which of the two members will have contact on the rigid switch first and at what temperature - axial stress that would develop on 1st member after the 2nd material fills in the gap safely. PLS. SHOW FULL SOLUTIONS WITH BRIEF EXPLANATIONS AND NECESSARY DIAGRAMS...
An 8 inches diameter piston is pushed inside the cylinder having an 8.005 inches diameter. The gap is filled with a lubricant (v= 0.003 ft^2/s, SG=0.80). If the piston is moving at 0.5ft/s, find the frictional resistance wherein there is an engagement of 10 ft.
Prob # 1.A round bar made from SAE 1025 low Carbon steel is to support a direct tension load of 50,000 lbs. Using a factor of safety of 4, and assuming that the stress concentration factor, k = 1, What is the suitable standard diameter. Yield stress is 40,000 psi. a. 3 ½ inch b. 2 ¼ inch c. 2 9/16 inch d. 1 ½ inch
Verify if my answers are correct: P =1000 N Q =1300 N C =216000 N.mm
Derive an expression for the critical thickness of insulation of cylindrical pipe. Explain in detail.