An axial-flow pump delivers 300TERS cec AT a net head of 6om when rotating at 200orpm. s ericency is 80 percent. Ip the same pump was operated at 2,tco rpm, what wtauld be the Net head Flow rate Q, and the power delivered by the shaft forhomobgous condition? A Hnz - 764m G2 = 368 sec BP 36.04 bkw B Hnz C) Hhz = 8.24 m; Q2 = 372 sec ; BR = 40-14 bkw %3D 8-04m O2= 364 sec, BR- 34.24 bkw %3D a. 14 hkiy

An axial-flow pump delivers 300TERS cec AT a net head of 6om when rotating at 200orpm. s ericency is 80 percent. Ip the same pump was operated at 2,tco rpm, what wtauld be the Net head Flow rate Q, and the power delivered by the shaft forhomobgous condition? A Hnz - 764m G2 = 368 sec BP 36.04 bkw B Hnz C) Hhz = 8.24 m; Q2 = 372 sec ; BR = 40-14 bkw %3D 8-04m O2= 364 sec, BR- 34.24 bkw %3D a. 14 hkiy

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Similar questions

A centrifugal pump(efficiency 86%) lifts water through a total height of 42m from reservoir to discharge. Pumping is through 300m of 75mm diameter pipe at the rate of 20li/s. If pipe friction factor, f = 0.025, what KW is required? Answer: 9
A 70 percent efficient pump delivers water at 20°C fromone reservoir to another 20 ft higher, as in Fig. . Thepiping system consists of 60 ft of galvanized iron 2-in pipe,a reentrant entrance, two screwed 90° long-radius elbows,a screwed-open gate valve, and a sharp exit. What is theinput power required in horsepower with and without a 6°the well-designed conical expansion added to the exit? Theflow rate is 0.4 ft3/s.
A Kaplan turbine working under a head of 43 m deve-lops 15,400 B.H.P. The dia of theboss is 0"3 times the dia ofrunner. Determine the speed and dia of runner, if speed ratio is2, flow ratio as 0-65 and overall efficiency as 91%.
The date for a certain installation are as follows Net Head = 454 m, BP = 57,200 bkw, n = 750 rpm, ηT = 90%. What type of turbine was used? A. Impulse turbine B. Kaplan turbine C. Propeller turbine D. Francis turbine
Q:/ Discuss the relation betwveen the head pressure and flow rate for the benefits of connecting the pumps in parallel ?
The suction diameter of 60mm reads 2psi vaccum and 50mm diameter discharge with 250kpag. The suction water level is 5m above water pump center line and discharge water level is 25m above the pump center line. The total head loss at suction and discharge is 2m. If discharge is 0.01m3/s, find the horsepower needed to pump the water for 80% pump efficiency. ANSWER: 8.15 hp
A piston PDP has a 5-in diameter and a 2-in stroke andoperates at 750 r/min with 92 percent volumetric effi ciency.(a) What is its delivery, in gal/min? (b) If the pump deliversSAE 10W oil at 20°C against a head of 50 ft, what horsepoweris required when the overall effi ciency is 84 percent?
A pump is needed to drain an excavation at a construction site. The excavation has alength of 50m, width of 50m, and a depth of 4m. The surface of the water in the excavation lies at adepth, H=3m, from the top the of the excavation. An old, radial flow, 1000W pump is immediatelyavailable for use; however, the total pump-motor efficiency, e, is only 50%. Estimate the drawdown inthe excavation in the first 4 hours of pumping. Neglect the change in H with increasing time. Neglectany head loss in the hose/pipe connected to the pump. (Hint: utilize the Pout equation, consider analternative definition of discharge as a change in volume over a change in time). Assume a specificweight of 9.79kN/m 3 .
The general energy balance equation for a turbine is: Qnet + Wnet = ΔmH + ΔKE + ΔPE What does it mean when the term ΔmH is negative? Describe what changes occured to the fluid's energy, and where it went.
A hydroelectric plant has 14 identical Francis turbines, a gross head of 245 m, and a volume flow rate of 11.5 m3 /s through each turbine. The water is at 25°C. The efficiencies are ?turbine = 95.9%, ?generator = 94.2%, and ?other = 95.6%, where ?other accounts for all other mechanical energy losses. Estimate the electrical power production from this plant in MW
A centrifugal pump is pumping water at the design conditions with a flowrate of 2300 gpm and a tangential velocity of U2=65ft/s. The flow passage area at the outlet is A2=1ft2. About 5% of the flow is recirculated internally and pumped again. The actual head rise of the pump is 94ft and the blade angle at outlet is 28º. Knowing that the total number of blades is Zb=24, the power needed to operate the pump is Ps=65hp. Take g = 9.81 m/s2 = 32.2 ft/s2 & ρw = 998 kg/m3 =1.94 Slug/ft3. Estimate the theoretical head of the pump in ft using Stodola’s formula (Hi). Determine the mechanical efficiency of the pump (ηm).
Before solve the problem please understand the question. Give me right solution according to the question. A flow rate of 0.14 m3 / s is required from a centrifugal pump with an outer radius of 23cm and rotating at 900 rpm. The width of the propeller is b = 8cm (at the outlet). Assuming 73% efficiency, what motor horsepower is required if the outlet angle is 165º? Suppose the pallets occupy 5% of the exit area.