An electric load consists of a resistor, a capacitor and an inductor connected in series. The total impedance of the load is connected across 240430° V, compute the following: a. The load impedance b. The source current in polar form c. The phase shift between the current and the voltage d. The power factor of the load

An electric load consists of a resistor, a capacitor and an inductor connected in series. The total impedance of the load is connected across 240430° V, compute the following: a. The load impedance b. The source current in polar form c. The phase shift between the current and the voltage d. The power factor of the load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

a. Find the total impedance ZT in polar form b. Draw the impedance diagram c. Find the current I and voltages VR , VL , and Vc in phasor form d. Draw the phasor diagram of the voltages E, VR, VL and VC, and the current I. e. Verify Kirchhoff’s voltage law around the closed loop. f. Find the average power delivered to the circuit g. Find the power factor of the circuit, and indicate whether it is leading or lagging.
The voltage across a load is v(t)=1042 cos(ωt+10°) V, and the current through the load is i(t) = 202 cos(ωt-20°) A.The reference direction for the current points into the positive reference for the voltage. Determine the power factor, the power, the reactive power, and the apparent power for the load. Is this load inductive or capacitive?
The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal impedance of the sinusoidal voltage source is 4+j7 Ω. 1. a) What is the maximum average power delivered to ZL?2. b) What percentage of the average power delivered to the lineartransformer is delivered to ZL?
a. Find the total admittance and impedance in polar form b. Draw the admittance and impedance diagram c. Find the voltage E and currents IR , IL , and Ic in phasor form d. Draw the phasor diagram of the currents Is, IR, IL and IC, and the voltage E. e. Verify Kirchhoff’s current law at one node f. Find the average power delivered to the circuit g. Find the power factor of the circuit, and indicate whether it is leading or lagging. h. What happened if R= 10 Ω
We have a load with an impedance given by Z= 30+j40 Ω.The voltage across this load is V = 15002 ∠30° V.Is the load inductive or capacitive? Determine the power factor, power, reactive power, and apparent power delivered to the load.
For the given circuit (A) Find the TOTAL IMPEDANCE Zr in polar form, the CURRENT I and the VOLTAGES VR and VL im phasor form. (B) Find the power factor of the circuit, and indicate whether it is leading or lagging. (C) Find the sinusoidal expressions for the voltages and current if the frequency is 60Hz.
For the following numeric values, determine theaverage power, P, the reactive power, Q, and the complex power, S, of the circuit shown in Figure. Note: phasor quantities are rms.
A circuit consists of a series connected 84 Ω resistor and a 163 mH inductor. The circuit supply is a 121 V rms source with a frequency of 42 Hz. Ultimately, you need to calculate the average power dissipated in the circuit. You should have found the polar form of the complex current. The average power dissipated in the resistive and reactive circuit is: ?=??cosφ where φ is the phase of the current, and V and I are the rms values. Finally, calculate the circuit Power Factor (cos?) where φ is the phase of the current. Finally, will the circuit Power Factor cos? be lagging or leading?
In the circuit below, find the value of the load impedance ZL, which must be connected to the output of the circuit for MAXIMUM POWER TRANSFER. If this load impedance you found is connected, the amplitude of the current that will pass through the circuit, the phase angle and the angular frequency of the circuit are given in which option correctly. AB=61 AB=16 Answers I need: current= ?? angular frequency = ?? phase angle = ??
The line with symmetrical spacing then the equilateral spacing (Deq) for the three-phase inductance calculation is D12=D23=D31=D. Select one: True False
Consider the circuit shown. Find the following: a. Total load impedance seen by the voltage source. b. Complex power delivered by the source. c. Average power delivered by the source. d. Reactive power delivered by the source. e. Load power factor and power factor angle.
a) Find the average power dissipated in the line shown.b) Find the capacitive reactance that when connected in parallelwith the load will make the load look purely resistive.c) What is the equivalent impedance of the load in (b)?d) Find the average power dissipated in the line when the capacitivereactance is connected across the load.