An orifice of 2.58 cm diameter is placed in a pipe of 5.1 cm diameter. The pipe delivers oil of specific gravity of 0.8. if the pressure difference on the two sides of the orifice is measured by a mercury-oil manometer and the differential gauge reads 125 mm of mercury, calculate the Actual and Ideal rate of flow in liter per second if Ca=0.63 P1 5.1 cm diameter

An orifice of 2.58 cm diameter is placed in a pipe of 5.1 cm diameter. The pipe delivers oil of specific gravity of 0.8. if the pressure difference on the two sides of the orifice is measured by a mercury-oil manometer and the differential gauge reads 125 mm of mercury, calculate the Actual and Ideal rate of flow in liter per second if Ca=0.63 P1 5.1 cm diameter

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

n orifice of 10 cm diameter is fitted in a 25 cm diameter pipe that carries oil of specific gravity 0.9. The mercury manometer attached to the orifice shows a reading of 75 cm. Calculate the oil flow rate through the pipe. Assume coefficient of discharge for orifice as 0.7.
Show complete solution with diagram: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127 cm manometer filled with mercury is used to measure the pressure difference across the venturi meter. If the manometer reads 101.6 cm when 15 °C water is flowing through the pipe, what is the flow rate of water (m3/min)? Assume that the venturi meter coefficient of discharge equals 0.98.
A 30-cm by 15-cm Venturi meter is mounted on a vertical pipe with the flow upward. One hundred twenty-six (126) liters per second of oil (s.g. = 0.80) flows through the pipe. The throat section is 15cm above the upstream section. If Cv=0.957, what is the difference in pressure between the inlet and the throat?
3.A horizontal venturimeter with inlet diameter 30 cm and throat diameter 15 cm is used to measure the flow of oil of sp. gr. 0.8. The discharge of oil through venturimeter is 50 litres/s, find the reading of the oil-mercury differential manometer. Take Cd = 0.98
: A Venturimeter is inserted in a 150mm diameter pipe carrying an oil of specific gravity 0.85. If the differential head indicated by the mercury manometer is 0.25m and the rate of flow is 80lit/sec, find the diameter of Venturimeter at its throat. Take coefficient for Venturimeter as 0.97.
A test on 30-cm-diameter pipe with water showed a gage difference of 33 cm on mercury-water manometer connected to two piezometer rings 120 m apart. The flow was 0.23 m/s. What is the friction factor?
Apply Bernoulli equation in solving the problem: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127 cm manometer filled with mercury is used to measure the pressure difference across the venturi meter. If the manometer reads 101.6 cm when 15 °C water is flowing through the pipe, what is the flow rate of water (m3/min)? Assume that the venturi meter coefficient of discharge equals 0.98.
C3. An oil of specific gravity 0.85 is flowing through a horizontal venturimeter fitted to a 240 mm diameter pipe at the rate of 102 liters/s and throat diameter is 98 mm. The entrance and throat of the venturimeter are connected in the two limbs of a U-tube mercury manometer. The difference in mercury level shows 835 mm. Calculate (i) the head difference in m of oil, (ii) the theoretical discharge in m3/s, (iii) the actual discharge in m3/s, and (iv) the coefficient of discharge of a venturimeter. If instead of a U-tube mercury manometer, the pressure gauges are inserted at the entrance and throat of venturimeter. Find (v) the pressure at the throat in N/mm2, if the entrance pressure gauge shows0.126 N/mm2. (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) (i) the head difference in m of oil (ii) the theoretical discharge in m3/s (iii) the actual discharge in m3/s (iv) the coefficient of…
Oil relative density (rd = 0.88) flows in an inclined pipe at a rate of 0.15 m/s as shown in Fig. If the differential reading in the mercury manometer is 915 mm, calculate the power that the pump supplies to the oil if head losses are negligible.
Oil of specific gravity 0.70 and dynamic viscosity of 0.05Pa-s flows at a rate of 100lit/sec through a 80m of 150mm diameter pipe. If the head lost is 4m, determine the reynolds number, maximum velocity in m/s, maximum shear stress in Pa , Velocity 40mm from centerline of pipe in m/s.
A Liquid is flowing through a pipe of 50 mm diameter under a pressure of 2.943x10^5 N/m2 (gauge) and with mean velocity of 200 cm/s. Find the density of the liquid, if the pipe is located 5m above the datum and total head is 35.204m.
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa