B4. An orifice meter with orifice area 931 mm² is inserted in a pipe of area 1862 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 75 cm of mercury. Find the rate of flow of oil of sp. gr. 0.75 when the co-efficient of discharge of the orifice meter = 0.6. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) Head of water (in m) The discharge of water through pipe (in Litres/sec)

B4. An orifice meter with orifice area 931 mm² is inserted in a pipe of area 1862 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 75 cm of mercury. Find the rate of flow of oil of sp. gr. 0.75 when the co-efficient of discharge of the orifice meter = 0.6. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) Head of water (in m) The discharge of water through pipe (in Litres/sec)

Name: An orifice meter with orifice area 931 mm² isinserted in a pipe of ar
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: An orifice meter with orifice area 931 mm² isinserted in a pipe of area 1862 mm2 .The pressureB4.difference measured by a mercury oil differentialmanometer on the two sides of the orifice metergives a reading of 75 cm of mercury. Find the rateof flo

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An 11.5-in-diameter centrifugal pump, running at1750 r/min, delivers 850 gal/min and a head of 105 ftat best efficiency (82 percent). (a) Can this pump operateefficiently when delivering water at 20°C through200 m of 10- cm-diameter smooth pipe? Neglect minorlosses. (b) If your answer to (a) is negative, can thespeed n be changed to operate efficiently? (c) If youranswer to (b) is also negative, can the impeller diameterbe changed to operate efficiently and still run at1750 rev/min?
3.A horizontal venturimeter with inlet diameter 30 cm and throat diameter 15 cm is used to measure the flow of oil of sp. gr. 0.8. The discharge of oil through venturimeter is 50 litres/s, find the reading of the oil-mercury differential manometer. Take Cd = 0.98
A 20 hp pump with a suction from an open reservoir (10 m abovethe pump) has a flow rate of 125 m3/hr and a suction pipe of 150mm diameter. Determine the discharge pressure of the pump if itpumps water to a tank 15 m above the pump. Discharge pipediameter of the pump is 100 mm.
The difference in head registered between two limbs of a mercury gauge, with water above the mercury and connected to a horizontal venturi meter, is 20 cm. If the venturi has a pipe and throat diameter of 15 cm and 7.5 cm, respectively, determine the discharge through the meter assuming a coefficient of discharge of 0.97.
Water flows through a venturi meter whose inlet diameter is 31 cm and throat diameter is 19 cm. The pressure at the inlet is 755kPa and at the throat 550 kPa. Determine the discharge in cumecs. Neglect head loss.
water flows through a horizontal venturyi meter whose inlet diameter is 33 cm. and throat diameter is 21 cm. the pressure at the inlet is 775 kpa and at the throat is 584 kPa. determine the discharge in L/s. neglect head lost.
The head-versus-flow-rate characteristics of a centrifugalpump are shown in Fig.. If this pump drives water at20°C through 120 m of 30-cm-diameter cast iron pipe,what will be the resulting flow rate, in m3/s?
If the difference between the total pressure and static pressure in an air duct is measured by a pitot tube to be 6.5 cm H2O, what is the flow velocity in m/s? Density of water is 998 kg/m3, and g = 9.81 m/s2. 3 signififcant figures answer
Water at 20°C is to be pumped through 2000 ft of pipe fromreservoir 1 to 2 at a rate of 3 ft3/s, as shown in Fig. P6.62.If the pipe is cast iron of diameter 6 in and the pump is75 percent efficient, what horsepower pump is needed?
Water at 20° C is siphoned from a reservoir as shown. For d = 8 cm and D = 16 cm, determine (a) the minimum flow rate that can be achieved without cavitation occurring in the piping system and (b) the maximum elevation of the highest point of the piping system to avoid cavitation. (c) Also, discuss the ways of increasing the maximum elevation of the highest point of the piping system to avoid cavitation.
A ventury meter used to measure the liquid from the reservoir. The cross-sectional area at the inlet and throat are 4.536 x 10-3 m? and 1.134 x 103 m? with the flowrate of water is 9167 cm¾s. The level difference of mercury in manometer u tube shows the reading of 266 mm. Determine the flowrate coefficient. Given the specific gravity of mercury 13.6.
A pipe discharges 142 lps of water into a reservoir at a point 1.85 mbelow the water surface. At point A the diameter is 25.4 cm and the center of thepipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.