c An overhanging W920×449 rolled-steel beam supports a load P as shown.Knowing that P= 700 kN, a = 2.5 m, and oa =100 MPa, determine (a) themaximum value of the normal stress o, in the beam, (b) the maximum valueof the principal stress omx at the junction of the flange and web, (c) whetherthe specified shape is acceptable as far as these two stresses are concerned.

Answered: Image /qna-images/answer/27d9c51b-da7d-495c-a10d-208f89a83f6c.jpg

An overhanging W920×449 rolled-steel beam supports a load P as shown. Knowing that P= 700 kN, a = 2.5 m, and o =100 MPa, determine (a) the maximum value of the normal stress om in the beam, (b) the maximum value of the principal stress omax at the junction of the flange and web, (c) whether the specified shape is acceptable as far as these two stresses are concerned.

An overhanging W920×449 rolled-steel beam supports a load P as shown. Knowing that P= 700 kN, a = 2.5 m, and o =100 MPa, determine (a) the maximum value of the normal stress om in the beam, (b) the maximum value of the principal stress omax at the junction of the flange and web, (c) whether the specified shape is acceptable as far as these two stresses are concerned.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 6 *12-in. timber beam has been strengthened by bolt-ing to it the steel reinforcement shown. The modulus of elasticity for wood is 1.8 * 106 psi and for steel 29 *106 psi. Knowing that the beam is bent about a horizontal axis by a couple of moment 450 kip·in., determine the maximum stress in (a) the wood, (b) the steel.
A 6 * 10-in. timber beam has been strengthened by bolting to it the steel straps shown. The modulus of elasticity is E= 1.5 *106 psi for the wood and E= 30 * 106 psi for the steel. Knowing that the beam is bent about a horizontal axis by a couple of moment 200 kip·in., determine the maximum stress in (a) the wood, (b) the steel.
Knowing that the allowable stress in section ABDC is 70 MPa. 22 mm 50 mm 15 mm 15 mm a) Draw the FBD of section ABDC. (Hint: carry P force to the ABDC section with its corresponding moment) b) Determine max P load by applying stress formula for eccentrically loaded members. (Hint: 0 = 77MY, (Hint: Be careful about signs (+ for tension – for compression) while using stress formula) c) Which surface (AC/BD) of the section yields in which scenario (compression/tension). d) Determine the strains on each surface AC and BD (Hint: be careful about signs (+ for tension – for compression) while using stress formula) e) Draw the strain diagram. (E=70 GPa) f) Determine position of neutral axis from point A. (Does it cross the line AB?) A
| 275 kN (a) Knowing that ol =160 MPa and ra =100 MPa, select the most economical metric wide-flange shape that should be used to support the loading shown. (b) Determine the values to be expected for 275 kN om, Tm, and the principal stress omax at the junction of a flange and B D -3.6 m- 1.5 m 1.5 m the web of the selected beam. For (b) check at Points B and C
A 6-x 10-in. timber beam has been strengthened by bolting two - x 2-in. steel straps to it as shown below. The moduli of elasticity are 1.5 x 106 psi for the wood and 30 x 106 psi for the steel. Knowing that the beam is bent about a horizontal axis by a bending moment of 200 kip in, determine (a) The maximum flexural stress in the wood. (b) The maximum flexural stress in the steel. 10 in. T 6 in.. wood 2 x 3/8 in. steel
Q.I. An I-section beam, 150 mm wide by 250 mm deep, with flange and web of thickness 20 mm is used as a simply supported beam over a span of 7 m. The beam carries a distributed load of 6 kN/m and a concentrated load of 30 kN at mid-span. Determine: (a) the second moment of area of the cross- section of the girder, (b) the maximum stress set-up. 20 mm 150 mm B 20 mm 250 mm 20 mm
The rectangular beam ABC, 129 mm wide by 354 mm deep, is supported by a pin at A and the cable CD. Determine the normal stress (in MPa) at the bottom of the beam and at asectionofthebeam 1.09 m from the pin if P = 493.54 kN. mq2 1.png ... 4 3 B 2 m 1.0 m →|
The rigid beam BCis supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm?. The cross- sectional area of rod (2) is 17 mm?. For a uniformly distributed load of w = 4.2 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L= 4.85 m. (1) (2) B |C
The 6x12-in timber beam has been strengthened by bolting to it the steel reinforcement shown. The modulus of elasticity for wood is 1.8x10° psi and for steel, 29x10° psi. Knowing that the beam is bent about a horizontal axis by a couple of moment M = 450 kip -in, detemine the maximum stress in (a) the wood, (b) the steel. M in.
QI/Beams AB Problems, BC, and CD have the cross section shown and are pin-connected at B and C. Knowing that the allowable normal stress is +110 MPa in tension and -150 MPa in compression, (a) determine the largest permissible value of P (b) determine distance a. 12.5 mm -200 mm- 150 mm 24 m 2.4 m 2.4 m --l|- 12.5 mm
An S150x 18.6 steel beam is loaded and supported as shown. On a section 3m to the right of A, determine (a) the flexural stress at a point 25mm below the top of the beam and (b) the maximum flexural stress on the section.
The 6 × 12-in. timber beam has been strengthened by bolting to it the steel reinforcement shown. The modulus of elasticity for wood is 1.8 × 106 psi and for steel, 29 × 106 psi. Knowing that the beam is bent about a horizontal axis by a couple of moment M = 458 kip·in., determine the maximum stress in the wood and in the steel. The maximum compressive stress in the block of wood is ksi (include a negative sign). The maximum tensile stress in the steel is ksi.