Answer the following questions. Figure 1: For questions 1-2 R1=1000 ww R1-3000 R2-2000 1. What is the total circuit resistance? a) 54 ohms b) 154 ohms c) 300 ohms d) 600 ohms 2. If E 100 V, what is the current in the circuit? a) 0.06 A b) 0.167 A c) 6.0 A d) 16.7 A Figure 2: For questions 3-5 R1-100 R2-40 www www R4-200 R3-60 3. What is the total circuit resistance? a) 4 ohms b) 40 ohms c) 60 ohms d) 200 ohms

Answer the following questions. Figure 1: For questions 1-2 R1=1000 ww R1-3000 R2-2000 1. What is the total circuit resistance? a) 54 ohms b) 154 ohms c) 300 ohms d) 600 ohms 2. If E 100 V, what is the current in the circuit? a) 0.06 A b) 0.167 A c) 6.0 A d) 16.7 A Figure 2: For questions 3-5 R1-100 R2-40 www www R4-200 R3-60 3. What is the total circuit resistance? a) 4 ohms b) 40 ohms c) 60 ohms d) 200 ohms

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 14RQ: 14. A 6-V lead-acid battery has an A-hr rating of 180 A-hr. The battery is to be load-tested. What...

See similar textbooks

Similar questions

True or False: Ohms law applies to all types of electrical circuits.
14. A 6-V lead-acid battery has an A-hr rating of 180 A-hr. The battery is to be load-tested. What should be the test current, and what are the maximum permissible amount and duration of the voltage drop?
A resistor has a resistance of 20 ohms at 30 degrees Celsius and 32 ohms at 90 degrees Celsius. Find its resistance at 125 degrees Celsius. Determine also the temperature coefficient at 100 degrees Celsius. (Please Show Complete solution and write properly) (Round off the final answer to the 4th decimal if possible and box the final answer)
14] Encode Decimal '-124' using Two's Complement. Express your answer in Hex. 15] How much Current is passing through a 470 ohm Resistor that is dropping 3.3 Volts? Express your answer in Decimal with 2 digits of significance. 16] How many Volts are being dropped by a 2.7k Ohm Resistor if it is passing 75uA? Express your answer in Decimal with 2 digits of significance.
1. Using Volt-Ohm-Multimeter (VOM), explain how would you measure the resistance of a) R1, b) resistance of R2, c) resistance of R1 + R2
Consider the circuit shown in (Figure 1). Suppose that R= 150 Ohm. Please answer in typing format solution please only typing format solution
Subject: FUNDAMENTALS OF ELECTRICAL CIRCUITSPlease provide an answer with READABLE solution for the question in the picture.
Since R1=3198.15ohm, R2=9694.26ohm and Ri=Infinite in the circuit given in the figure, write the equivalent resistance in Ohms between the terminals A-B. When making your transactions, 2 digits will be taken after the dot. Write the result you found according to the margin of error of ± 10% (plus/minus ten percent). While writing the answer, a space is written in front of the value (kOhm, ohm, V, A) etc. values should not be written. Only numeric values should be entered. A period (.) must be used as a decimal separator. Do not use thousands separators (do not use signs such as semicolons). An example notation is given below. Let the value you find be 1.15Kohm. You should write 1150.00 in the box. Let the value you find be 432.63 ohms. You should write 432.63 in the box. If the correct answer is X, values entered in the range of X ± (X*10/100) (including limits) will be accepted. If x=50, it will be accepted as between [45,55].
Subject: FUNDAMENTALS OF ELECTRICAL CIRCUITSPlease provide an answer with solution for the question in the picture.
Need answer to these 2 questions plz
In the figure, an electrical circuit arranged using R1, R2, R3 resistors is seen on the experiment board. a) Draw the scheme of this circuit. Since R2 = 20, the current flowing through the battery is Ibat = 5mA, the current and voltage values read by the ammeter and voltmeter are I = 3mA and V = 15V, answer the following questions. a) What is the voltage across the resistor R3? b) How many volts is the voltage, E between the ends of the power supply? c) What is the intensity of the current I3 passing through R3? d) How many Ohms is the resistance of R3? e) What is the equivalent resistance of the resistor group?
Kirchhoff's Law Pls each question based on the table. 1. What can you say about the current (I) values across each individual resistor?2. What happens to the measured voltage (V) across each individual resistor?3. Compare the theoretical and measured values for the resistances (R) of each individual resistor and the corresponding voltage (V) across them. 4. Explain the differences between theoretical and measured values referred to above? 5. Compare the voltage of Source 1 to the sum of V1 and V2. Explain. 6. Compare the voltage of Source 2 to the sum of V4 and V5. Explain.