As shown in the figure below, you have a system including a Polyethylene vessel with mass Mvessel = 0.229 kg. The vessel contains water with mass Mwater = 0.399 kg. Both the vessel and water are initially at a temperature of 54.6 degrees Celsius. You add steam into the system. The steam has an initial temperature of 167.4 degrees Celsius and a mass of Msteam = 10.9564 kg. The system will reach equilibrium with all the water having vaporized at some final temperature above 100 degrees Celsius.

As shown in the figure below, you have a system including a Polyethylene vessel with mass Mvessel = 0.229 kg. The vessel contains water with mass Mwater = 0.399 kg. Both the vessel and water are initially at a temperature of 54.6 degrees Celsius. You add steam into the system. The steam has an initial temperature of 167.4 degrees Celsius and a mass of Msteam = 10.9564 kg. The system will reach equilibrium with all the water having vaporized at some final temperature above 100 degrees Celsius.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.3P

See similar textbooks

Similar questions

A 5L rigid container contains Acetylene initially at gage pressure and temperature of 100 KPa and 300 K, respectively. Because of the leaks in the fittings of the vessel, the gage pressure dropped to 80KPaand the temperature decrease to 200K, determine the mass of the Acetylene that leaked out.
During processing in a steel mill, a 375kg steel casting at 800 degrees is quenched by plunging it into a 500-gal oil bath, which is initially 75 degrees . After the casting cools and the oil bath warms , what is the final tempertature of the two? The weight per unit volume of the oil is 7.5 lb/gal.
An insulated evacuated tank of 1.75-m> volume is attached to a line containing steam at 400 Wa and 513.15 K (240°C). Steam flows into the tank until the pressure in the tank reaches 400 kPa. Assuming no heat flow from the steam to the tank, prepare graphs showing the mass of steam in the tank and its temperature as a function of pressure in the tank
A prototype boiler that contains 5 kg of saturated steam at a pressure of 482.5kPa. Determine the amount ofheat which must be rejected in order to reduce the quality to 60%. (a) What will be the pressure andtemperature of the steam at this new state? Compute for the (b) heat, (c) internal energy, (d) entropy, and (e)enthalpy at this new state. Note: Consider a constant pressure process.
1. Saturated steam at a pressure of 25 psia is sprayed into a stream of moist air. The initial condition of the air is 55 dry-bulb temperature and 35 F de-point temperature. The mass rate of air flow is 2000 lb per min. Barometric pressure is 14.696 psia. Determine how much steam must be added in lb per min to produce a saturated air condition, b) the resulting temperature of the saturated air.
A rigid tank contains 2kg of saturated water vapor mixture at temperature of 50 degrees C and quality of 70%. Electrical heating is used to convert this to superheated steam at 1.2MPa and 250 degrees C. If the heat transer from the tank during this process is 500kJ, what is the required electrical energy? What happens if the process continues ti 10 minutes, what is the required electrical power?
The tank contains 2kg of water at 20C, 1 atm. The tank is heated. When the tank pressure reaches 300kpa, the valve opens and steam starts escaping. Heating continues and steam continues to escape while the pressure remains constant until half of the mass escapes. At this time the tank is filled with saturated vapor at 300 kpa, and the valve closes. Question: Determine the volume of the tank and the amount of supplied heat.
A heat-insulated (adiabatic) constant volume vessel divided by a metal curtain. The volume of the compartments is not equal!. Initially, one of the chambers contains 2.5 kg of compressed s-phase water at a temperature of 60 °C and a pressure of 600 kPa. The other chamber is empty (vacuum). Then the metal curtain is lifted and the water covers the entire volume. Since the final pressure is 10 kPa, calculate the volume of the container and the final temperature of the water
The movement of 4.2 kilograms of gas through an isentropic pump requires 85 kilowatts of power. Find the power saved or increased if the process is changed to be isothermal and the Cv=0.886 kJ/kg-K and the Cp=1.758 kJ/kg-K. The final pressure is 22 psia, and the initial pressure was 850 mmHg, and the initial temperature was 38°C.
A 10-ft3 vessel of hydrogen at a pressure of 305 psia is vigorously stirred by paddles until the pressure becomes 400 psia. Determine ΔU, ΔH, and paddle work (Wp). Assume the vessel is fully insulated
3.0 kg of steam at a pressure of 100 kPa are contained in a rigid sealed tank of volume 5.95 m3. The steam begins to cool as heat is transferred to the atmosphere. When the internal pressure reaches 10 kPa, the tank walls will collapse.a) What is the initial temperature of the steam in the tank (in oC)?b) What will the temperature be in the tank when the walls collapse (in oC)?c) Attheinstantofcollapse,whatisthemassofwaterinthevapourandliquidstate (in kg)?d) Deduce the work done for this process
For the situations below briefly explain how you obtained the values and provide the numerical answer. A) When 1 kg saturated water vapor is condensed to a saturated liquid water at 325 Kpa, what is the change in its volume? B) What is the specific internal energy liquid water at 280 degree Celsius and 7500 Kpa?