As we learned, Bernoulli's equation is not to be used in many situations. Let's say you are examining changes between two points in a flow. Which ONE of these scenarios could you appropriately use Bernoulli's equation on? O A turbine is situated between the two points There are large changes in kinetic energy between the two points The mass flow rate between the two points changes with time There are large changes in density between the two points There are large viscous losses between the two points QUESTION 10 A 12 cm diameter jet of air strikes a plate positioned normal to the flow, with all air deflected away parallel to the plate. If the air flows at a speed of 20 m/s, what is the force needed to held the plate in place? Do not use a linear momentum correction factor. O 0.272 N 10.9 N 4510 N 5.45 N 0.340 N

As we learned, Bernoulli's equation is not to be used in many situations. Let's say you are examining changes between two points in a flow. Which ONE of these scenarios could you appropriately use Bernoulli's equation on? O A turbine is situated between the two points There are large changes in kinetic energy between the two points The mass flow rate between the two points changes with time There are large changes in density between the two points There are large viscous losses between the two points QUESTION 10 A 12 cm diameter jet of air strikes a plate positioned normal to the flow, with all air deflected away parallel to the plate. If the air flows at a speed of 20 m/s, what is the force needed to held the plate in place? Do not use a linear momentum correction factor. O 0.272 N 10.9 N 4510 N 5.45 N 0.340 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. Show that a source flow is a physically possible incompressible floweverywhere except at the origin. Also show that it is irrotationaleverywhere.
Consider steady flow of water through an axisymmetric garden hose nozzle. The axial component of velocity increases linearly from uz, entrance to uz, exit as sketched. Between z = 0 and z = L, the axial velocity component is given by uz = uz,entrance + [(uz,exit − uz,entrance)/L]z. Generate an expression for the radial velocity component ur between z = 0 and z = L. You may ignore frictional effects on the walls.
As a young engineer, you have been tasked to select the location of a wind turbine based on the details of the location and relevant specification below:Air densityAverage air velocityDiameter of wind turbine bladesLOCATION A1.29 kg/m3 54 km/h 70 mLOCATION B1.21 kg/m3 63 km/h 60 m By comparing the amount of power generated (in MW) at Location A and Location B, determine the location that will give the optimum wind power generation.9 kg of Refrigerant 134-a is initially at 26.69°C with enthalpy of 100 kJ/kg. Heat is transferred to the refrigerant under a constant-pressure process until the entropy of the refrigerant reaches 0.9795 kJ/kg.K.(i) Determine the final temperature of the refrigerant(ii) Calculate the boundary work, Wb, in kJ.Assist your answer with a proper P-v diagram indicating the properties,process, and boundary work region clearly.(iii) Explain the reason behind the high amount of boundary work obtained in (ii).Assist your explanation with relevant sketching.
Pump specific speed and turbine specific speed are “extra” parameters that are not necessary in the scaling laws for pumps and turbines. Explain, then, their purpose.
Water at 20◦C flows along the streamlines shown in Figure3.11. The (gauge) pressure, velocity, and elevation at Point1 are 15.0 kPa, 1.0 m/s, and 5.02 m, respectively, and thevelocity and elevation at Point 2 are 0.5 m/s and 5.21 m,respectively. Estimate the pressure at Point 2. The given answer was P2 = 13.5 kPa. Show detailed solution pls thank you.
For a flow in the xy plane, the x component of the velocity is given as u=3x2y-y3. Determine the y component for steady state and incompressible flow. Does this result also apply to unstable, incompressible flow? Why is that? How many possible y components are there? Discuss.
Liquid flows out of a hole in the bottom of a tank as in FinConsider the case in which the hole is very small compared to the tank (d ≪ D). Experiments reveal that average jet velocity V is nearly independent of d, D, ? , or ? . In fact, for a wide range of these parameters, it turns out that V depends only on liquid surface height h and gravitational acceleration g. If the liquid surface height is doubled, all else being equal, by what factor will the average jet velocity increase?
04/13/2021 For this exercise Study and Derive the Bernoulli equation starting with the application of Newton’s second law to a fluid particle.
The entrance-to-exit area ratio of streamtube is given as 2. Consider incompressible flow entering the streamtube. Which of the following statements is true? A. mass flow decreases and static pressure decreases B. mass flow decreases and static pressure increases C. mass flow remains unchanged and velocity of the flow decreases D. mass flow remains unchanged and velocity of the flow increases
In Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.
Unless stated otherwise take:Patm = 10^5, P(water) = 1000 kg/m^3 ; P(air) = 1.2 kg/m^3 ; g = 9.8m/s^2gage pressure Pg = P - PatmUnless specified otherwise assume uniform velocity profiles in duct locations.The Bernoulli eq’n (BE), P + ½ρV2 + ρgz = constant In this formulation the scalar variable z is the vertical height measured opposite the direction of g (z is always taken up independent of your coordinate system; pgz is potential energy)This BE is only valid along a streamline in steady state flow, when viscous friction effects can be ignored, called “ideal” fluid motion, and the density is assumed to be constantthe differential radial component of –?P + ρg = ρawith the centripetal acceleration , ar = - V^2/r , to get dp/dr = ρgr + ρV^2/rThe Bernoulli eq’n is often divided through by the constant ρg ≡ γ so that each term has units of length, a height or “head” : (P/ ρg) + (V2/2g) + (z) = constant. Q = VA = flow rate = constant, as a second eq’n to solve for an unknown velocity. the…
Q6.Starting from the fundamentals wind speed and the power relations, derive an expression for power in the upstream wind. (students should think logically and then answer this question)