Water flows steadily and smoothly along a horizontal pipe through a contraction and out into the atmosphere soon after as sketched below. Area B Area A The volume flux is Q. Estimate the height h for which water can be sucked into the main flow from a lower reservoir open to the atmosphere. Q^2/(2*g)*((A^2-B^2)/(A^2*B^2)) Your last answer was interpreted as follows: Q? ( A? - B 2g The variables found in your answer were: [A, B, Q, g] X Incorrect answer.

Water flows steadily and smoothly along a horizontal pipe through a contraction and out into the atmosphere soon after as sketched below. Area B Area A The volume flux is Q. Estimate the height h for which water can be sucked into the main flow from a lower reservoir open to the atmosphere. Q^2/(2g)((A^2-B^2)/(A^2*B^2)) Your last answer was interpreted as follows: Q? ( A? - B 2g The variables found in your answer were: [A, B, Q, g] X Incorrect answer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 2.00 m, r1 = 1.30 m, b2 = 0.85 m, and b1 = 2.10 m. The runner blade angles are ?2 = 71.4° and ?1 = 15.3° at the turbine inlet and outlet, respectively. The runner rotates at n. = 160 rpm. The volume flow rate at design conditions is 80.0 m3/s. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (MW) and required net head (m).
Water exits a 1-cm diameter outlet of a faucet. Estimate the maximum speed that would result in a laminar flow if the water temperature is 50°C. Assume Re = 2000 a. 558 m b 6.15 m c7.71 m d 845 m
Water at 20 ° C flows steadily through a reducing pipe bend,as in Fig. P3.77. Known conditions are p 1 = 350 kPa, D 1 =25 cm, V 1= 2.2 m/s, p 2 = 120 kPa, and D 2 = 8 cm.Neglecting bend and water weight, estimate the total forcethat must be resisted by the flange bolts.
Air flows at high speed through a Herschel venturi monitored by a mercury manometer, as shown in Fig. The upstream conditions are 150 kPa and 80°C. If h = 37 cm, estimate the mass flow in kg/s.
pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
An orifice on vertical wall has a head of 1.13m of oil ( sp.gr.=0.89). It discharges 6192N of oil in 88 seconds . The trajectory measures yield x = 2.4m and y = 1.37m . Assuming the area of the opening is 25cm2, Calculate Coefficient of Contraction, Coefficient or Velocity
A Francis radial-flow hydroturbine is being designed with the following dimensions: r2 = 2.00 m, r1 = 1.42 m, b2 = 0.731 m, and b1 = 2.20 m. The runner rotates at n. = 180 rpm. The wicket gates turn the flow by angle ?2 = 30° from radial at the runner inlet, and the flow at the runner outlet is at angle ?1 = 10° from radial. The volume flow rate at design conditions is 340 m3 /s, and the gross head provided by the dam is Hgross = 90.0 m. For the preliminary design, irreversible losses are neglected. Calculate the turbine specific speed of the turbine. Provide answers in both dimensionless form and in customary U.S. units. Is it in the normal range for a Francis turbine? If not, what type of turbine would be more appropriate?
A Francis radial-flow hydroturbine is being designed with the following dimensions: r2 = 2.00 m, r1 = 1.42 m, b2 = 0.731 m, and b1 = 2.20 m. The runner rotates at n. = 180 rpm. The wicket gates turn the flow by angle ?2 = 30° from radial at the runner inlet, and the flow at the runner outlet is at angle ?1 = 10° from radial. The volume flow rate at design conditions is 340 m3 /s, and the gross head provided by the dam is Hgross = 90.0 m. For the preliminary design, irreversible losses are neglected. Calculate the inlet and outlet runner blade angles ?2 and ?1, respectively, and predict the power output (MW) and required net head (m). Is the design feasible?
A bicycle tire is fi lled with air at an absolute pressure of169.12 kPa, and the temperature inside is 30.0 °C. Supposethe valve breaks, and the air starts to exhaust out of the tireinto the atmosphere (pa = 100 kPa absolute and Ta =20.0 °C). The valve exit is 2.00 mm in diameter and is thesmallest cross-sectional area of the entire system. Frictionallosses can be ignored here; one-dimensional isentropicflow is a reasonable assumption. (a) Find the Machnumber, velocity, and temperature at the exit plane of thevalve (initially). (b) Find the initial mass flow rate out ofthe tire. (c) Estimate the velocity at the exit plane using theincompressible Bernoulli equation. How well does thisestimate agree with the “exact” answer of part (a)? Explain.
Ethanol at 20°C flows at 125 U.S. gal/min through a horizontalcast iron pipe with L= 12 m and d = 5 cm. Neglecting entranceeffects, estimate (a) the pressure gradient dp/dx, (b) thewall shear stress τw, and (c) the percentage reduction in frictionfactor if the pipe walls are polished to a smooth surface.
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 6.60 ft, r1 = 4.40 ft, b2 = 2.60 ft, and b1 = 7.20 ft. The runner blade angles are ?2 = 82° and ?1 = 46° at the turbine inlet and outlet, respectively. The runner rotates at n. = 120 rpm. The volume flow rate at design conditions is 4.70 ×106 gpm. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (hp) and required net head (ft).
Water fl owing in a smooth 6-cm-diameter pipe entersa venturi contraction with a throat diameter of 3 cm.Upstream pressure is 120 kPa. If cavitation occurs in thethroat at a fl ow rate of 155 gal/min, what is the estimatedfl uid vapor pressure, assuming ideal frictionless fl ow?( a ) 6 kPa, ( b ) 12 kPa, ( c ) 24 kPa, ( d ) 31 kPa, ( e ) 52 kPa