Assume air at 20°C and atmospheric pressure on a smooth flat plate with a speed free current of 25 m/s (kinematic viscosity of 1.5x10-5 m2/s and density 1.2 kg/m3). The plate is 4 m long and 1.5 m wide. If the boundary layer is initially laminate and then become turbulent boundary layer with a transition Re of 5x10^5: a) What is the drag coefficient for the plate? b) What is the drag force on the entire plate? c) At what distance x from the plate the profile becomes turbulent. d) What is drag force on the turbulent part? e) What is the drag force on the laminar part

Assume air at 20°C and atmospheric pressure on a smooth flat plate with a speed free current of 25 m/s (kinematic viscosity of 1.5x10-5 m2/s and density 1.2 kg/m3). The plate is 4 m long and 1.5 m wide. If the boundary layer is initially laminate and then become turbulent boundary layer with a transition Re of 5x10^5: a) What is the drag coefficient for the plate? b) What is the drag force on the entire plate? c) At what distance x from the plate the profile becomes turbulent. d) What is drag force on the turbulent part? e) What is the drag force on the laminar part

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.49P

See similar textbooks

Similar questions

Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the thickness of the hydrodynamic boundary layer at a distance 0.3 m from the leading edge of the surface.
Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart. Estimate the distance from the entrance to the point where the boundary layers meet.
From Table the drag coefficient of a wide plate normalto a stream is approximately 2.0. Let the stream conditionsbe U∞ and p∞. If the average pressure on the front of theplate is approximately equal to the free-stream stagnationpressure, what is the average pressure on the rear?
Consider a 102 mph airflow over a flat plate with a span of 9.7 ft and a planform area of 60 ft2. The boundary layer transitioned from laminar to turbulent. If the total skin friction drag for the laminar section is 0.858 lbs, determine the location of the transition point. Assume SSLC, Provide answer in feet and round off answer to the nearest thousandths.
The airfoil section of the wing of the British Spitfire of World War II fame is an NACA 2213 at the wing root, tapering to an NACA 2205 at the wing tip. The root chord is 8.33 ft. The measured profile drag coefficient of the NACA 2213 airfoil is 0.006 at a Reynolds number of 9 × 106. Consider the Spitfire cruising at an altitude of 19000 ft. Assume that μ varies as the square root of temperature. At this velocity and altitude, assuming completely turbulent flow, estimate the skin-friction drag coefficient for the NACA 2213 airfoil, and compare this with the total profile drag coefficient. Calculate the percentage of the profile drag coefficient that is due to pressure drag. (Round the final answer to three decimal places.) The skin-friction drag coefficient for the NACA 2213 airfoil is .
A wing of 2 percent camber, 5-in chord, and 30-in span istested at a certain angle of attack in a wind tunnel with sealevelstandard air at 200 ft/s and is found to have lift of 30 lbfand drag of 1.5 lbf. Estimate from wing theory (a) the angle ofattack, (b) the minimum drag of the wing and the angle of attackat which it occurs, and (c) the maximum lift-to-drag ratio.
Derive an expression for turbulent boundary layer thickness over a flat plate
A ship is 180 m long and has a wetted area of 8000 m2. Estimate the power expended against drag when the ship moves at 3.86 m/s in seawater at 20 °C
Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m.Calculate the boundary layer thickness at the trailing edge of plate and drag force on one sideof plate if:a. Surface of plate is smooth.b. Surface of plate is rough.The air properties at 20 °C are: Density, ? = 1.2 kg/m3and dynamic viscosity, ? = 1.8x 10-5kg/m·s and kinematic viscosity, ν = 1.516×10-5m2/s
Consider a flat plate at zero angle of attack in an airflow at standard sea level conditions (p∞ = 1.01 × 105 N/m2 and T∞ = 288 K). The chord length of the plate (distance from the leading edge to the trailing edge) is 2 m. The planform area of the plate is 40 m2. At standard sea level conditions, μ∞ = 1.7894 × 10−5 kg/(m)(s). Assume the wall temperature is the adiabatic wall temperature Taw. Calculate the friction drag on the plate assuming a turbulent boundary layer for a freestream velocity of (a) 100 m/s, and (b) 1000 m/s.
Explain briefly in your own words (parts a-d)a) Why doesn’t the surface roughness affect the pressure drop in a laminar pipe flow? b) For bluff bodies, the drag coefficient decreases abruptly when the flow becomes turbulent. Why? c) Consider a spinning ball (in the clockwise direction) moving with a velocity U. Explain how the lift force is formed on the ball and show its direction. Uwd) For flow over streamlined bodies, drag force usually increases when the flow becomes turbulent.Why? e) Consider a pipe with a radius R and length L (extending from (1) to (2)). Inside the pipe there is a solid cylinder with a radius k×R (k  1). The planes (1) and (2), separated by a distance L have pressures P1 and P2 respectively, with P1 > P2. At t = 0, the inner solid cylinder suddenly begins to be pulled at a constant speed U in the negative z direction. Thefluid is an incompressible Newtonian liquid with dynamic viscosity μ and density ρ. In orderto find the solution for the velocity field in…
a)What is the impact of increasing Reynolds number on skin friction and pressure drags over an airfoil? What can be happened for separation in this case? b) What is an adverse pressure gradient and where does it occur on an airfoil (show that on a sketch)? c) Why lift-to-drag ratio is an important parameter for an aircraft? d)How can changing in altitude affect the aircraft power required, PR? Show thatmathematically and graphically?