Explain the following 68000 assembly program using flowchart. A8, B8, and R8 are three 8-bit variables. What is the purpose for this program? Pick up two different addressing modes from the program, what type of addressing mode: are they? (Assembly language instruction are provided as attached.) 1daa A8 adda B8 ok3 under3 1daa #127 ok3 1daa #-128 R8 bvc err3 bpl bra under3 ok3 staa

Explain the following 68000 assembly program using flowchart. A8, B8, and R8 are three 8-bit variables. What is the purpose for this program? Pick up two different addressing modes from the program, what type of addressing mode: are they? (Assembly language instruction are provided as attached.) 1daa A8 adda B8 ok3 under3 1daa #127 ok3 1daa #-128 R8 bvc err3 bpl bra under3 ok3 staa

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Given a 8-bit number at memory location 2050H. Write 8085 instruction to move the value stored at the following locations: Register B Accumulator 2052H Write a single program and show register and accumulator screenshot and also attach memory view. In sim8085 software.
6.) Select all the 8088 input signals that can cause the microprocessor to take an interrupt. a.) OSC b.) INTA c.) NMI d.) READY e.) INTR f.) IRQ 7.) Given the 8088 instruction "INT nn", how many possible types of interrupts are there for the 8088? a.) 2 b.) 4 c.) 8 d.) 256
Part 1:Compile the assembly code for the following C code. Part 2: What is the process for calculating the total number of RISC-V instructions needed to execute the function? Can you find an exact solution? If so, what is that? If not, why not?
Describe I/O Direct addressing mode. Also, provide an example of an instruction that applies this addressing mode.
Continuing with a 32 Khz system clock/8000 Khz instruction clock, assuming a pre-scalar of1:1 (i.e. no prescalar), and 16-bit operation, if TMR0 is initialized to 64536, how many timeswill TMR0 need to be incremented before it overflows? How many instructions cycles will that take?
Write a Verilog code with testbench for 16-bit up/down counter with synchronous reset and synchronous up/down.If up/down is set the counter is up counter and if it is not set, the counter is a down counter. submit the module code, testbench code, and the simulation results. PLEASE EXECUTE CODE IN VERILOG
If the current value of the stack segment register and stack pointer are C00016 and F F0016, respectively, what is the address of the current top of the stack ?
The processor has performed the following addition operation: 0x01A0+ 0xC410------0xC5B0 What decimal numbers did the processor add up, and what is the result of the addition if the programmer chose these numbers to be signed 16-bit number, where the lower four bits represent the fractional part of the number?
1. Design a 16 - to - 1 multiplexer using 4- to-1 multiplexer. 2. Using K- Map, simplify the following Boolean expression : Y = Σ (1,3,5,7,9,10,11,13,14,) 3. Build the logic circuit for the following function using Programmable Logic Array (PLA). ?? = ??? + ??? + ??? + ??? ?? = ??? + ??? + ??? + ???
The one-bit half adder's function? Total inputs and outputs? What logic gates did it use?
In a simple copy machine, a stop signal, S, is to be generated to stop the machine operation and energize an indicator light whenever either of the following conditions exists: (1) there is no paper in the paper feeder tray; or (2) the two micro-switches in the paper path are activated, indicating a jam in the paper path. The presence of paper in the feeder tray is indicated by a HIGH at logic signal P. Each of the micro-switches produces a logic signal (Q and R) that goes HIGH whenever paper is passing over the switch to activate it. Design and build the logic circuit to produce a HIGH at output signal S for the stated conditions, and implement it using the two-input NAND chip.
In a simple copy machine, a stop signal, S, is to be generated to stop the machine operation and energize an indicator light whenever either of the following conditions exists: (1) there is no paper in the paper feeder tray; or (2) the two micro-switches in the paper path are activated, indicating a jam in the paper path. The presence of paper in the feeder tray is indicated by a HIGH at logic signal P. Each of the micro-switches produces a logic signal (Q and R) that goes HIGH whenever paper is passing over the switch to activate it. (3) Regardless the state of the previous two statements the stop signal is active if there is no internet connection to the machine or if the inside temperature sensor is active (This sensor is active if the inside temperature of the machine reaches a certain threshold temperature). Design and build the logic circuit to produce a HIGH at output signal S for the stated conditions.