At a critical point in a component, the state of stress is given as Oxx = 100 MPa, Oyy = 220 MPa, oxy = Oyx = 80 MPa and all other stress components are zero. The yield strength of the material is 468 MPa. The factor of safety on the basis of maximum shear stress theory is (round off to one decimal

At a critical point in a component, the state of stress is given as Oxx = 100 MPa, Oyy = 220 MPa, oxy = Oyx = 80 MPa and all other stress components are zero. The yield strength of the material is 468 MPa. The factor of safety on the basis of maximum shear stress theory is (round off to one decimal

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.1P: The rails of a railroad track are welded together at their ends (to form continuous rails and thus...

See similar textbooks

Related questions

Q: The load on square section bar consists of a transverse shear force of 12 kN together with an axial…

A: Given: P=20 kNFt=12 kNσy=260 MPaf=1.8ν=0.28

Q: Maximum Principal Stress Theory is not good for brittle materials. a) True b) False

A: Given statement - Maximum Principal Stress Theory is not good for brittle materials.

Q: he values of stress amplitude and stress ratio

A: Given ; From the given figure; Fluctuating fatigue load Find the stress amplitude and stress ratio ?…

Q: Q1) A steel bolt, 2.5 cm in diameter, carries a tensile load of 40 kN. Estimate the average tensile…

Q: Q2// Determine the diameter of a circular rod made of ductile material with a fatigue strength…

A: Given, Fatigue strength, se'=270 MPa=270 N/mm2 Tensile yield strength, syt=370 MPa=370 N/mm2 The…

Q: An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 358 MPa, and at compression Suc…

A: Given data as per question Ultimate strength at tension Sut = 358 MPa Compression Suc = 1,000 MPa…

Q: A 400 ft long elevator cable (diameter of 1 inch) is made of 4130 steel with a yield strength of 120…

Q: In figure below, if the stress is applied at a frequency of 10 Hz,the material fails in 16minutes…

Q: Bar of steel, (yield strenght Sy = 559 MPa) is subjected to the following stresses; σx = 176 MPa ,…

Q: QUESTION 4 A spherical pressure vessel is made of ASTM A517-F steel and operates at room…

A: according to the given data

Q: Required information The part shown is loaded at point C with 290 N in the positive x direction and…

A: Given: The load at C, P = 290 N The load at E, Q = 200 N The diameter of the pipe, d = 12 mm

Q: The principal stresses at a point in a critical section are sigma_{1} = 60MPa sigma_{2} = 5MPA and…

Q: Determine the strength of the bedrock granite. Assume you sampled the granite where it was exposed…

A: For the Triaxial compression test Test Confining pressure σd…

Q: For the given fluctuating fatigue load, the values of stress amplitude and stress ratio are…

A: From the given figure, Maximum stress in the cycle = σmax = 250 MPa Minimum stress in the cycle =…

Q: A pipe with a wall thickness of 6 mm is designed to operate at the hoop stress of 600 MPa and the…

A: Given Data ⇒ Material - Stainless steel Wall thickness of the pipe is (t)=6 mm Hoop stress is σh=600…

Q: lameter 20mm. The bar A tensile test is carried out on a bar of mild yields under a load of 8KN; it…

A: Part A) Write the equation for tensile stress at the yield point as follows.

Q: Q3/ Thickness of plate is 5mm and its yield stress is 630 MPa with endurance limit equals 225 MPa,…

Q: A force F, = 450lb is applied to the bracket shown. Shaft AB is made of ASTM Gray cast iron. Specify…

A: Consider M as the bending moment of the shaft and T as the torque on applied on the shaft. Write the…

Q: A cylindrical pressure vessel has an internal diameter of 1600 mm and is subject to an internal…

A: Given, d=1600 mm p=30 bar = 3 MPa = 3 N/mm2 t= 15 mm σu= 600 N/mm2 ηc = 50% ηL = 80%

Q: pressure vessel 300 mm in diameter has a uniform thickness of 6 mm. The vessel contain gas under…

Q: A bar of 4340 steel has an Sy = 50 ksi. Which of these statements is true: If Sy = 50 ksi, than the…

Q: Q.2. A bolt is subjected to a tensile load of 18 kN and a shear load of 12 kN. The materia has an…

A: Given data: Tensile load, FT = 18 kN. Shear load, Fs = 112 kN. Yield stress, σys = 328.6 MPa. The…

Q: An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 406 MPa, and at compression Suc…

Q: Q1. A bracket, as shown in Fig. is supported by 5 bolts, two at the bottom and three above.…

A: To find: The size of bolts. Given: The factor of safety is FOS=2. The number of bolts n=5. The yield…

Q: .A solid rod of 12 mm diameter was tested for tensile strength with the gauge length of 50 mm. Final…

Q: If failure normal stresses are 280MPA, 180MPA and 20OMPA for steel, aluminum and bronze…

A: Stress: When a component or a part is subjected to any external force, a resisting force will be…

Q: Bar of steel, (yield strenght Sy = 484 MPa) is subjected to the following stresses; σx = 176 MPa ,…

Q: A material is subjected to plane stress. Express the distortion energy theory of failure in terms of…

A: According to distortion energy theory for plane stress : σ12-σ1σ2+σ22=σY2 here, σ1,σ2 are principal…

Q: An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 356 MPa, and at compression Suc…

Q: An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 345 MPa, and at compression Suc…

A: The ultimate tensile strength (UTS) of a material is the highest stress it can withstand when…

Q: The factors that creep rate depends on? Write 4 of them. Plot the creep-load curve and show its…

Q: 7/8" Bolts Gusset t = 1/2" V Thickness plate Tension plate 3" A36 Steel 13" 3" P,= ? и 3" Find the…

A: There are 3 major modes of failure in this case: 1. Shear failure 2. Tensile failure of the plate 3.…

Q: Determine the yield strength of a material required such that the component would not fail when…

Q: man value of axial force and corresponding stress values. an value of torque and corresponding…

Q: A pipe with a wall thickness of 6 mm is designed to operate at the hoop stress of 600 MPa and the…

A: Given Data⇒ Hoop Stress σh=600 MPa Axial Stress σa=300 MPa Damage tolerance safety factor SFk=1…

Q: A mild steel rod is subjected to a design stress of 382.16 N/mm2. If the maximum allowable stress is…

A: given data:- design stress (Sd)=382.16 N/mm allowable working stress(Sw)=500 mpa…

Q: Q - 4) In buckling experiment a steel column ( E - 210 Gpa ) was examined in pin - fixed method . It…

A: Critical stress is stress which produces due to pressure or forces which does not exceed the elastic…

Q: The displayed piece is loaded at 300 N with C in the positive x direction and 200 N in the positive…

Q: The principal stresses at the critical point of a part were found to be as shown. Using the…

Q: A machine member is subjected to fluctuating stress O =0, cos(8 t). The endurance limit of the…

A: GIVEN DATA - σ=σo cos(8πt) σe=350MPa FACTOR OF SAFETY N=3.5 WE HAVE TO FIND VALYE OF ALLOWABLE…

Q: The brass has a shear modulus (G) of 40 GPa. In the torsion test calculated results, (G) was found…

Q: A machine element is subjected to loading as shown, assuming that load P is uniformly distributed…

A: Write the given data: D=90 mmd=60 mmdh=27 mmr=15 mmt=20 mmfor given steel:Syt =420 MPafor given cast…

Q: The top lid of a nuclear reactor is being held by clamping screws which are made of AISI 4340 steel…

A: We have to determine factors of safety guarding against yielding and the factor of safety guarding…

Q: Q.1: Ifa material is cast iron (ultimate tensile strength = 300 Mpa, ultimate compressive strength -…

A: Data given- Ultimate tensile strength = 300 MPa Ultimate compressive strength = 900 Mpa

Q: he principal stresses at a point in a critical section of a machine component are sigma_{1} = 60MPa,…

A: Given:σ1=60 MPaσ2=5 MPaσ3=-40 MPaσy=200 MPa

Q: Material J is suggested to be used as a rod with the applied stress up to 150 MPa. Material J has a…

A: Given data: ◆ The yield strength of material: σyield = 340 MPa ◆ The factor of safety: FOS = 2 ◆ The…

Q: Identity all applicable failure theories. O a. Octahedral shear stress theory O b. Modified-Mohr…

A: It's ductile material so failure occurs are as follows. e) Ductile coulomb Mohr theory c)…

Q: The maximum normal stress theory ( Tresca's Theory) the Determine lelement FS of the Tresca's,…

Q: A rod with diameter 12mm is initially measured and market at exactly 250mm apart. This material has…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

At a critical point in a component, the state of stress is given as Oxx =
100 MPa, Oyy =
220 MPa, Oxy = Oyx = 80 MPa and all other stress components
are zero. The yield strength of the material is 468 MPa. The factor of safety on
the basis of maximum shear stress theory is
(round off to one decimal

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 solution

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
The principal stresses at a point in a critical section of a machine component are sigma_{1} = 60MPa, sigma_{2} = 5MPa and sigma_{3} = - 40MPa For the material of the component, the tensile yield strength is sigma_{y} = 200 MPa According to the maximum shear stress theory,what is the factor of safety.
answer this ; The factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca criterion)
A bolt is subjected to a tensile load of 18kN and a shear load of 12kN. The material has an yield stress of 328.6Mpa. Taking factor of safety as 2.5, Determine the core diameter of bolt according to the following theories of failure. Take possion’s ratio as 0.298 (i) Maximum Shear stress theory and (ii) Distortion Energy theory (iii) Maximum stress theory (iv) maximum strain energy theory (v) Maximum total strain energy theory.
A material is subjected to plane stress. Express the distortion energy theory of failure in terms of sx, sy, and txy.
A spherical tank contains an internal pressure of 3.0 MPa, the diameter is 16 m, the yield stress is 490 MPa. and the factor of safety is 2.5. Determine the required thickness I to the nearest millimeter.
A rod with diameter 12mm is initially measured and market at exactly 250mm apart. This material has an ultimate of 400MPa. After a tensile load applied, distance between the marks was measured to be 250.26mm. E= 200GPa Determine : A. strain of the rod stress in the rod. B. the stress in the rod C. the factor of safety for the situation
If d=40 mm, L=796 mm, F=29 kN, T=1.7 kNm and fail stress=156 MPa, calculate the apparent factor of safety for this loading condition. Give your answer to 2 decimal places.
A test piece is cut from a brass bar and subjected to a tensile test. With a load of 6.4 kN the test piece, of diameter 11.28 mm, extends by 0.04 mm over a gauge length of 50 mm. Determine: (i) the stress, (ii) the strain, (iii) the modulus of elasticity. (b) A spacer is turned from the same bar. The spacer has a diameter of 28 mm and a length of 250 mm, both measurements being made at 20~ The temperature of the spacer is then increased to 100~ the natural expansion being entirely prevented. Taking the coefficient of linear expansion to be 18 x 10-6/~ determine: (i) the stress in the spacer, (ii) the compressive load on the spacer. rC.G.] [64 MN/m 2, 0.0008, 80 GN/m 2, 115.2 MN/m 2, 71 kN.] Could you please answer thisquestion fully? If you use * could you please explain what you mean by it! Thank You :)
What is the Weibull modulus of this material? Would you advise the use of a similar material with a Weibull Modulus of 16.3 and a mean failure stress of 485 MPa, if you anticipate that the peak stress on the material could be 430 MPa? a. 15.7 b. Yes c. 18.6 d. 13.4 e. No f. 17.1
If the principal stresses are of opposite signs, then failure occurs in the plane. True or false?