At the proportional limit, a 10.5-in. gage length of a 0.75-in. diameter alloy bar has elongated 0.0325 in. and the diameter has been reduced 0.0006 in. The total tension force on the bar was 13.75 kips. Determine the modulus of elasticity. O 12650 ksi O 13970 ksi O 10060 ksi O 8443 ksi O 10830 ksi

At the proportional limit, a 10.5-in. gage length of a 0.75-in. diameter alloy bar has elongated 0.0325 in. and the diameter has been reduced 0.0006 in. The total tension force on the bar was 13.75 kips. Determine the modulus of elasticity. O 12650 ksi O 13970 ksi O 10060 ksi O 8443 ksi O 10830 ksi

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.3P

See similar textbooks

Related questions

Q: 1. (A). A 25mm square cross-section bar of length 300mm carries an axial compressive load of 50KN.…

A: as per our guidelines I solved 1st question only

Q: Three steel rods (E = 200 GPa) supports a 50 kN load P. Each of the rods AB and CD has a 300 mm2…

A: Given data: The modulus of elasticity of steel rod is E=200 GPa The load acting on the rod is P=50…

Q: 1.1 A 25 mm square cross-section bar of length 300 mm carries an axial compressive load of 50 kN.…

A: Given data: lo=300 mP=50 kNE=200 GN/m2 Need to determine the stress and the change in length.

Q: The stress–strain diagram for a material can be approximated by the two line segments shown. If a…

A: From the curve, write the expression of the elastic modulus of the material. From the curve, write…

Q: A 10-mm-diameter rod has a modulus of elasticity of E = 100GPa. If it is 4 m long and subjected to…

A: Given: The diameter of the rod is d=10 mm The length of the rod is L=4 m The axial load on the rod…

Q: A steel [E = 200 GPa] rod with a circular cross section is 14-m long. Determine the minimum diameter…

A: Given:E=200 GPaL=14 mP=37 KN∆L=5 mm

Q: Question 53 What is the elongation of the aluminum bar with a dimension of 25 mm by 25 mm and length…

Q: The rod BD is made of material with G1= 137 GPa has a diameter 42 mm is bonded to the tube CA at…

Q: A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is…

A: Given data: Width of the block = 20 mm Modulus of rigidity of the block, G = 26 GPa

Q: Bar (1) has a cross-sectional area of 0.75 in.?. If the stress in bar (1) must be limited to 35 ksi,…

Q: The truss shown in the figure below is made from A992 steel rods having a diameter of 30 mm and…

Q: A bar of chocolate has length, thickness, and width measurements of 15mm each. The load applied to…

Q: A heavy uniform rod of length 'L' and material density '8' is hung vertically with its top end…

A: Given dataLength =Lmaterial density=δNeed to determine total elongation of the bar dew to itsown…

Q: Bar (1) has a cross-sectional area of 0.75 in.². If the stress in bar (1) must be limited to 39 ksi,…

A: Correct answer: (b) 17.55 kips

Q: The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of…

A: Given data:

Q: The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The…

Q: The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear…

A: Given data as per the question Applied load =370 KN Average shear stress =200Mpa

Q: A bar of 24-mm diameter and 400-mm length is acted upon by an axial load of 38 kN. The elongation of…

Q: The stress–strain diagram for a material can be approximated by the two line segments shown. If a…

A: Given data: Diameter of bar, d = 80 mm Length of the bar, L = 1.5 m = 1500 mm Let, A = area of the…

Q: 300 300 400 Rex 500KN 300KN + 200kN Axially loaded two-step rod The two-step steel rod is subjected…

Q: A metallic rod made of steel as shown below is used as support for a signage with length equal to…

Q: An elevator with a mass of 500 kg and is supported by a 20 mm diameter cable, 500 m long. When the…

A: Given:me=500 KgWl=7500 Nd=20 mmL=500 mE=200 GPa

Q: A bar has a length of 200 mm and cross-sectional area of 7500 mm2. Determine the modulus of…

A: Given F=50kN=50 x 10^3N l=200 mm A=7500 mm^2 E=0.075 mm

Q: 1. A frame is shown to the right. The link BC is t = 6mm thick (into the page) and has width, w…

Q: 4. The timber member has a cross-sectional area of 1750 mm and its modulus of elasticity is 12 GPa.…

A: Answer: The change in the total length of the member after the loads shown are applied is 2.5 mm.

Q: sectional area of Arod = 0.75 in². If a load of P = 24 kip is applied to the end of rod, determine…

Q: A 8- in long steel has a cross-sectional area of 0.25 in². After a load of 5000 lb has been applied…

Q: A steel column is of length 8m and diameter 600 mm with both ends hinged. Determine the crippling…

Q: The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear…

Q: 1. Neglecting the weight of the steel wire, determine its required diameter if it is 30 ft long,…

A: Given data, L= 30 ft = 360 in Elongation ∆L= 0.4 in P= 500 lb E= 49*10⁶ psi Stress limit s=…

Q: A bar having a length of 5 in. and a cross-sectional area of 0.7 in.2 is subjected to an axial force…

A: Here modulus of elasticity is given by E=σεWhere σ=Tensile Stressε=Tensile strainSo now tensile…

Q: 3. Determine the total elongation of the composite body carrying a tensile load of 5000 N. Assume:…

Q: 2. A bar having a length of 5 in. and cross-sectional area of 0.8 in? is subjected to an axial force…

A: Given:L=5 inA=0.8 in2F=8000 lb∆L=0.003 in

Q: Q.1 A rod is made of wrought iron and is secured to the piston by a tapered rod and nut and to the…

A: The critical load is the maximum load without causing lateral displacement (buckling). The column…

Q: A steel [E = 200 GPa] rod with a circular cross section is 9-m long. Determine the minimum diameter…

Q: A bar has a length of 200 mm and cross-sectional area of 7500mm^2. Determine the modulus of…

A: Given data: The length of the bar, L = 200 mm. The cross-section area of the bar, A = 7500 mm2.…

Q: The steel strip has a unifom thickness of 50 mm. Compute the elongation of the strip caused by the…

A: GIVEN DATA- a=120mm b=50mm t=50mm P=500KN L=1000mm E=200GPa WE HAVE TO FIND TOTAL ELONGATION

Q: A square steel bar is 50 mm on a side and 250 mm long. It is loaded by an axial tensile force of 200…

A: GIVEN DATA- SIDE OF SQUARE a=50mm L=250mm E=200GPa P=200KN POISSON RATIO=0.3 WE HAVE TO FIND…

Q: the bar shown is subjected if the length a = 584 mm a if the modulus of elasticity then, its new…

A: Any action that can change the state of motion is called force, Force is described by its magnitude,…

Q: Acolumn of rainforced concrete has steel reinforcing rods running through its entire length and…

Q: The cylindrical rod is made of steel with E = 30000 ksi and u = 0.3. P 10 kips d Id = lin. L=4 ft AL…

A: Option c is correct. Here negative sign shows that final diameter is lesser than initial diameter.

Q: Determine (a) the critical load for the steel strut, (b) the dimension d for which the aluminum…

A: Given data: A strut figure made up of steel material and Al material Esteel…

Q: Determine the stress in each section of the bar shown below, which is subjected to an axial tensile…

A: Stress is the degree or amount of force which is applied per unit cross sectional area. Strain is…

Q: QN 44 A C-frame subjected to a force of 15 kN is shown in Figure. It is made of grey cast iron FG…

A: Force = 15 kN FOS = 2.5 Sut = 300 N/mm2 As per guideline , I can only do 1 question at a time. So ,…

Q: The below column (diameter 1 in.) is subjected to a compressive force where the diameter is…

Q: The rod BD is made of materia with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at…

Q: A uniform edge load of 500 lb>in. and 350 lb>in. is applied to the polystyrene specimen. If…

A: To find The new dimension of a', b', t'. Given The length a is 2 in. The length b is 2 in. The…

Q: 1. (A). A 25mm square cross-section bar of length 300mm carries an axial compressive load of 50kN.…

A: Given data:- side of square cross-section, a=25mm ∴Area of cross-section, A=a2=252=625mm2 Length of…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

100%

- once answered correctly will UPVOTE!!

At the proportional limit, a 10.5-in. gage length of a 0.75-in. diameter alloy bar has elongated 0.0325 in. and the diameter has been
reduced 0.0006 in. The total tension force on the bar was 13.75 kips. Determine the modulus of elasticity.
O 12650 ksi
O 13970 ksi
O 10060 ksi
O 8443 ksi
O 10830 ksi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness ßRat A. Determine the critical load Pcr for the structure.
A steel [E = 200 GPa] rod with a circular cross section is 13-m long. Determine the minimum diameter D required if the rod must transmit a tensile force of 23 kN without stretching more than 4 mm. 13.18 mm 28.25 mm 20.13 mm 25.90 mm 21.81 mm
A bar having a length of 5 in. and a cross-sectional area of 0.7 in.2 is subjected to an axial force of 8000 lb. If the bar stretches 0.002 in., determine the modulus of elasticity of the material. The material has linear elastic behavior.
A straight bar 450 mm long is 10 mm in diameter for the first 200 mm length and 20 mm in diameter for the remaining length. If the bar is subjected to an axial push of 10 kN, determine decrease in length of the bar. Take modulus of elasticity of bar material E = 2 × 105 N/mm²
Four 10 kg masses are being supported by an 800mm solid rod. The rod is being supported at both ends, and the rest of the rod is suspended. Determine the smallest rod diameter to support the masses without bending the rod. Assume the Tensile Strength of the Rod material is 500 MPa
In a standard tensile test a steel rod of 7/8 in. in diameter is subjected to a tension force of 17 kips. Determine the ratio of the shear modulus to the modulus of elasticity of a material whose Poisson's ratio is 0.25.
Determine the width and thickness of the leaves (in mm) of a leaf spring using the following specifications: Total load = 140 kN; Number of springs supporting the load = 4; Maximum number of leaves = 10; Span of the spring = 1000 mm; Permissible deflection = 80 mm; Modulus of elasticity, E = 200 kN/mm2; and allowable stress in spring material is 600 MPa.
A bar has a length of 200 mm and cross-sectional area of 7500mm^2. Determine the modulus of elasticity of the material if it is subjected to an axial tensile load of 50 kN and stretches 0.075 mm. The material has linear-elastic behavior.
A bar has a length of 200 mm and cross-sectional area of 7500 mm2. Determine the modulus ofelasticity of the material if it is subjected to an axial tensile load of 50 kN and stretches 0.075 mm.The material has linear-elastic behavior.
A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and the length of the steel rod are given as 10 mm and 120 mm,respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,00053. Given that the total extension of the composite rod must not exceed 0,1624 mm and E for steel is 200 GPa, respectively. Determine : A) Strain in the steel rod B) Load carried by the steel and brass rods C) Modulus of elasticity for the brass
A 75 mm diameter compound bar is constructed by shrinking a circularbrass bush onto the outside of a 45 mm diameter solid steel rod. If thecompound bar is then subjected to an axial compressive load of 170 kN,determine the load carried by the steel rod. The modulus of elasticity for steel,Es = 200 GN/m2 , and brass, Eb = 100 GN/m2
Refer to the set of bars made of a material with a yield strength of 350 MPa, determine the minimum dimensions h1 and h2 required. Apply a safety factor FS = 1.5 without flux. Each bar is 12 mm thick