b) A 4 poles , 50HZ ,Y-connected three phase induction motor has the perphase equivalent circuit parameters of ( R1= R2= 0.12 , X1 = X2 = 0.6 , Xm=12 ) n and 2 = 20L0°. Use exact equivalent circuit to determine thefollowing at rated slip of 0.03:I.Stator currentI.Magnetizing currentII.Power factorIV.Developed torque

b) A 4 poles , 50HZ ,Y-connected three phase induction motor has the per phase equivalent circuit parameters of ( R1= R2= 0.12 , X1 = X2 = 0.6 , Xm =12 ) 2 and l2 = 20L0°. Use exact equivalent circuit to determine the following at rated slip of 0.03 : I. Stator current I. Magnetizing current II. Power factor Developed torque IV.

b) A 4 poles , 50HZ ,Y-connected three phase induction motor has the per phase equivalent circuit parameters of ( R1= R2= 0.12 , X1 = X2 = 0.6 , Xm =12 ) 2 and l2 = 20L0°. Use exact equivalent circuit to determine the following at rated slip of 0.03 : I. Stator current I. Magnetizing current II. Power factor Developed torque IV.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A three-phase, Y-connected, 220 V, 5 kVA, salient-pole synchronous generator is employed to supply power to a load with unitary fp. By means of a slip test, the direct-axis synchronous reactance is determined to be 12 Ω and the quadrature-axis synchronous reactance, 7 Ω. Consider that the rated current is delivered to the load at the rated voltage and that the armature resistance is negligible. (a) Calculate the corresponding value of the excitation voltage. (b) What is the value of the internal phase shift angle? (c) What is the value of the power angle?
A three-phase 60 Hz induction motor connected to a three-phase bus at rated voltage isoperating at a low slip condition (i.e s < 20%) resulting in a steady state speed of 1090 rpm.(a) How many poles does the motor have?(b) What is the percentage slip at the operating speed?(c) What is the corresponding frequency, (fr) of the currents and voltages induced in therotor winding?
A three-phase induction motor, operating at rated voltage and frequency, has a startingtorque of 1.35 times and a maximum torque of 2.2 times, both with respect to its rated-loadtorque. Ignoring the effects of the stator resistance and rotational losses and assumingconstant rotor resistance, determine the slip at the maximum torque;
A three-phase induction motor, operating at rated voltage and frequency, has a startingtorque of 1.35 times and a maximum torque of 2.2 times, both with respect to its rated-loadtorque. Ignoring the effects of the stator resistance and rotational losses and assumingconstant rotor resistance, determine the slip rated load, and the rotor current at starting (as a percentage of the rotor current at rated load). The slip at maximum torque is 0.343 if that helps.
a. A three-phase, 220-V, 60-Hz induction motor runsat 1,140 r/min. Determine the number of poles (forminimum slip), the slip, and the frequency of therotor currents.b. To reduce the starting current, a three-phasesquirrel cage induction motor is started byreducing the line voltage to Vs/2. By what factorare the starting torque and the starting currentreduced?
Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please
A three phase, 4 pole, 3300 V, 50 Hz, star connected Induction motor, has identical primary and referred secondary impedance of value 3+j9 Ohm per phase. Using the approximate circuit, calculate: A. The full load torque at rated slip of 5%. B. The maximum torque at normal voltage and frequency.
EMachines A 100 MVA, 11.5 kV 0.8 pf lagging 50-Hz two pole Y-connected synchronous generator has a per-unitsynchronous reactance of 0.8 and per-unit armature resistance of 0.012. A. What is its synchronous reactance and armature resistance in ohms?B. What is the magnitude of the internal generated voltage at the rated conditions? What is its torque angleat these conditions?C. Ignoring losses in this generator, what torque must be applied to its shaft by the prime mover at fullload?
Three-phase induction motor, 460 V 50 Hz, 4 poles, 50 hp with Delta, operating at 3.8% slip rated torque when receives Line Voltage 460 V, 50 Hz The parameters of the equivalent circuit per phase are as follows.R1 = 0.33, X1 = X2 = 0.42 and Xm = 30 Ohm / phase.Answer the following questions by neglecting the mechanical losses, Core losses and Stray load losses.A) Value of the rotor resistance R2 B) Maximum torque and rated speed C) line current and starting torque of motor
The full-load slip of 4-pole,60Hz,440v (line -to-line) three phase induction motor is 0.05. i.What is the speed of the rotating stator field?What is the frequencey (in Hz) of the rotor current. ii.When the output power of the motor is 90 hp at a speed of 1732rpm,rotational losses(which includes frictional and core losses) are 10,100W,while copper losses for both rotor and stator total 3700W.Determine the motor efficiency and line current,assuming the motor has a 0.8 pf lagging under these conditions.
A 75kW, 440V, 3-phase, 6-pole,50Hz wound rotor induction motor has a full load slip of0.04 and the slip at maximum torque of 0.2 when operating at rated voltage and frequencywith rotor winding short circuited at the slip rings. Assume the stator resistance androtational losses to be negligible. Find(a) Maximum torque(b) Starting torque(c) Full load copper loss.The rotor resistance is now doubled by adding an external series resistance.Determine(d) Slip at full load(e) full-load torque(f) slip at maximum torque
The primary leakage impedance and equivalent secondary impedance referred to stator atstandstill of a 3-phase, 220 V, 50-Hz, 4-pole induction motor are (0.4 + 3j)ohms and (1.2 + j1) ohms per phaserespectively. If the magnetizing current is neglected, determine the maximum torque the motor candevelop and slip at which it occurs.