(b) A multiple plate clutch has more number of clutch plates. A typical clutch consist of the following important components which are drive (friction) plates and driven (steel) plates. If a multiple plate clutch with an effective diameter of 250 mm and 150 mm are able to transmit 60 kW at 1200 rpm. Also the end thrust is given as 4.5 kN and coefficient of friction is 0.13. Answer below questions; (i) Determine torque to be carry by friction clutch. (ii) Calculate number of plates required with uniform wear and uniform pressure theory. Compare your results.

(b) A multiple plate clutch has more number of clutch plates. A typical clutch consist of the following important components which are drive (friction) plates and driven (steel) plates. If a multiple plate clutch with an effective diameter of 250 mm and 150 mm are able to transmit 60 kW at 1200 rpm. Also the end thrust is given as 4.5 kN and coefficient of friction is 0.13. Answer below questions; (i) Determine torque to be carry by friction clutch. (ii) Calculate number of plates required with uniform wear and uniform pressure theory. Compare your results.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single plate friction clutch with both sides of plate being effective is used to transmit power at an engine speed of 200rpm. It has outer and inner radii 10cm and 8cm respectively. Find maximum power transmitted and the corresponding axial thrust, if the maximum intensity of pressure is not to exceed 0.08N/mm2 . Assume coefficient of friction as 0.25.
3) A multiple disc clutch, steel on bronze, is to transmit 7 kW at 1000 rpm. The inner radius of thecontact is 50 mm and outer radius of the contact is 75 mm. The clutch operates in oil with an expected coefficient of "0.1". The average allowable pressure is 0.35 N/mm2. Determine the total number of steel and bronze discs.
In an open flat belt drive, a pulley of 800 mm diameter runs at 300 r.p.m. The coefficient of friction between the belt and the pulley is 0.25, the angle of lap is 170° and the maximum tension in the belt is 2000 N. The power transmitted is: 10.5 kW 9.4 kW 8.9 kW 7.6 kW None of the mentioned 13.1 kW
Mechanical Engineering In a lamellae clutch, the number of inner lamellae zi= 5 pieces, the number of outer lamellas zd=6 pieces. If the inner radius of the lamella is ri=70mm, the radius of the outer lamella is rd=120mm, the surface safety pressure of the lamella material is pem =0.8 MPa, the friction coefficient is u=0.1, what is the maximum power that the clutch can carry at n=120 rpm?
In a lamella clutch, the number of inner lamellae zi= 5 pieces, the number of outer lamellas zd=6 pieces. If the inner radius of the lamella is ri=70mm, the radius of the outer lamella is rd=120mm, the surface safety pressure of the lamella material is pem =0.8 MPa, the friction coefficient is u=0.1, what is the maximum power that the clutch can carry at n=120 rpm?
A multi-plate clutch has four pairs of frictional surfaces, each of internal diameter 120 mm and external diameter 200 mm. If the coefficient of friction is 0.3 and the uniform pressure condition can be assumed, what is the required spring force when the plates transmit 20 kW at 1400 rpm?
Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm², load factor is 2 and the mean diameter to face width ratio is 6.
A soft cone clutch has a cone pitch angle of 10°, mean diameter of 300 mm and a face width of 100 mm. If the coefficient of friction is 0.2 and has an average pressure of 0.07 N/mm2 for a speed of 500 rpm, find : (a) the force required to engage the clutch; and (b) the power that can be transmitted. Assume uniform wear. [Ans. 1470 N ; 10.4 kW]
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.3; working speed= 600 rpm; friction surface number= 2; If required clamping force = 2917 N, clutch outer diameter = 400 mm, clutch inner diameter = 160 mm, what is the transmitted power?
A conical Clutch transmits rotation from one rotating shaft to another though frictional forces on the conical face. The following data is for a conical clutchInside Diameter 25.0 mmOutside Diameter 100 mmCoefficient of Friction 0.33Axial Force 1000NIncluded angle 100 degreeRotational speed 1500rev/minuteCalculate the Torque and Power that can be transmitted without slipping using both Uniform Pressure Theory and Uniform Wear Theory
1. A multiple friction clutch is required to transmit 89.52 kW at 3000 rpm. The plates are alternatively of steel and phosphor bronze and they run in oil. The coefficient of friction is 0.08. The internal radius of the friction surface is 0.8 times the radius of the external surface. The axial pressure is limited to 20 x 104 N/m2 . If the maximum diameter of the frictional surface is not to exceed 250 mm, determine the number of plates required.