b) Figure 2 is the tin-gold phase diagram, for which only single-phase regions are labeled. Write one (1) entectic point reaction and label all the non-label regions (i) - (viii). 1000 800 L (viii) Temperature (°C) 600 400 200 0 (Sn) (i) B (ii) (iii) 20 40 60 80 Composition (wt% Au) Figure 2 Tin-gold phase diagram (v) Y 3 (vi) (iv) (vii) 1 In 100 (Au)

b) Figure 2 is the tin-gold phase diagram, for which only single-phase regions are labeled. Write one (1) entectic point reaction and label all the non-label regions (i) - (viii). 1000 800 L (viii) Temperature (°C) 600 400 200 0 (Sn) (i) B (ii) (iii) 20 40 60 80 Composition (wt% Au) Figure 2 Tin-gold phase diagram (v) Y 3 (vi) (iv) (vii) 1 In 100 (Au)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question: For 5.7 kg of a magnesium–lead alloy of composition 50 wt% Pb–50 wt% Mg, is it possible, at equilibrium, to have α and Mg2Pb phases with respective masses of 5.13 and 0.57 kg? If so, what will be the approximate temperature of the alloy? If such an alloy is not possible, then explain why.
For the Pb-Sn phase diagram showing incomplete solid solution, which of the Hume-Rothery rules are violated.
Referring to Figure 1, please answer the following [NOTE: SHOW YOUR WORK on Figure 1]:a. provide the specific name for the phase boundary lines denoted by A and B. b. identify the phases present at equilibrium in the phase fields denoted by C, D, and E. c. identify the specific name for the point denoted by F. d. What is the maximum solid solubility of Mg in Al? At what temperature does it occur? e. An Al-Mg alloy (10 wt% Mg, 90 wt% Al) is heated slowly (to insure equilibrium) from a temperature of 200 C: i. At what temperature does the first liquid phase form? ii. What is the composition of the liquid phase at the temperature in part i.? iii. At what temperature does complete melting (no solid phase remaining) occur? iv. What is the composition of the last solid remaining prior to complete melting? f. Using the equilibrium phase diagram of Figure 1, identify the phases present, their compositions, and their relative mass fractions at equilibrium for a 70 wt% Mg – 30 wt% Al…
Consider the binary eutectic copper-silver phase diagram shown below. Make phase analysis of a 80 wt % Ag–20 wt% Cu alloy at the temperatures (a) 900°C, and (b) 780°C-ΔT. In the phase analysis include: (I) phases present, (ii) chemical compositions of phases, (iii) mass fractions of phases, and (iv) sketch of microstructure.
Phase Diagrams: You are given the lead tin (Pb-Sn) phase diagram. Below the eutectic isotherm is identified as the two phase region a + B. a) At 30wt % Sn, in the circles below draw the microscopic observations evolving at 3000C, 2250C, and 1000C for this hypoeutectic alloy. b) At a temperature just above the isotherm at 1830C, for the 30 wt% Sn Alloy, calculate the fractions of each phase present at equilibrium and the corresponding composition of each phase.
a-Arrange in a table the number of phases that can be observed at R.T in the range starting from zero to 6.67%C in an "Equilibrium Phase Diagram" and the corresponding three of the mechanical properties.b- Explain with examples the solid-solution, eutectic and peritectic observed phases.c- Draw the .microstructure of each phase
10.27 A hypothetical A-B alloy of composition 55 wt% B-45 wt% A at some temperature is found to consist of mass fractions of 0.5 for both a and 8 phases. If the composition of the B phase is 90 wt B-10 wt% A, what is the composition of the a phase?
For an alloy containing 40% p Sn - 60% p Pb at a temperature of 150°C: (a) Which phases are gifts? (b) What is (are) the composition(s) of this (s) phase(s)? (c) Calculate as quantities relatives of each phase present in terms of the mass fraction. (image attached below)
In a binary phase diagram ( pressure omitted) what is the maximum number of phases that can coexist for at least one degree of freedom?
An alloy of 30 wt % Pb and 70 wt % Sn is slowly cooled from 250°C to 27°C: d) What is the amount and composition of each phase that is present at 183°C - ∆T ? e) What are the amounts of each phase present at room temperature? f) Draw the microstructure 183°C + ∆T and 183°C - ∆T in 2 cm diameter circle.
Use the phase diagrams for Cu-Ni and Cu-Ag systems below to answer the question: Based on the mechanism, would you expect a solution containing 80 wt% Cu to be stronger if the remaining 20% of the alloy was Ni or Ag? Briefly explain
From the phase diagram of the Fe-0.25wt%C alloy below, determine the phase fraction and elemental composition of the resulting phase immediately after solidification across the eutectoid line (725 C). a.alpha_eutectoid = 96.6 wt% and cementite = 29.85 wt% b.alpha_eutectoid = 96.6 wt% and cementite = 3.4 wt% c.alpha_eutectoid = 1.05 wt% and cementite = 29.85 wt% d.alpha_eutectoid = 29.85 wt% and cementite = 1.05 wt%