B4. An orifice meter with orifice area 848mm2 is inserted in a pipe of area 1696 mm2.The pressure difference measured by amercury oil differential manometer on thetwo sides of the orifice meter gives a readingof 80 cm of mercury. Find the rateflow ofoil of sp. gr. 0.75 when the co-efficient ofdischarge of the orifice meter = 0.54.(Enter only the values by referring the unitgiven. Also upload the hand writtenanswers in the link provided)Head of water (in m)The discharge of water through pipe (inLitres/sec)

Name: B4. An orifice meter with orifice area 848mm2 is inserted in a pipe o
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: B4. An orifice meter with orifice area 848mm2 is inserted in a pipe of area 1696 mm2.The pressure difference measured by amercury oil differential manometer on thetwo sides of the orifice meter gives a readingof 80 cm of mercury. Find the rateflow o

Given fluid in pipe is oil with specific gravity of 0.75 and not water .Hence there is correction in…

Engineering

Mechanical Engineering

B4. An orifice meter with orifice area 848 mm2 is inserted in a pipe of area 1696 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 80 cm of mercury. Find the rate of flow of oil of sp. gr. 0.75 when the co-efficient of discharge of the orifice meter = 0.54. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) Head of water (in m) The discharge of water through pipe (in Litres/sec)

B4. An orifice meter with orifice area 848 mm2 is inserted in a pipe of area 1696 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 80 cm of mercury. Find the rate of flow of oil of sp. gr. 0.75 when the co-efficient of discharge of the orifice meter = 0.54. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) Head of water (in m) The discharge of water through pipe (in Litres/sec)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe whose axis is horizontal, is full of water in motion. At a section A, the velocity of water is recorded as 54000dm/hrandd the pressure is equilavent tp 14.07m of water. if the pipe tapers gradually from 150mm diameter to A to 100mm diameter at B. determine the preesure at B.
The pump in Fig. draws gasoline at 20 ° C from areservoir. Pumps are in big trouble if the liquid vaporizes(cavitates) before it enters the pump. ( a ) Neglecting lossesand assuming a fl ow rate of 65 gal/min, fi nd the limitationson ( x , y , z ) for avoiding cavitation. ( b ) If pipe frictionlosses are included, what additional limitations might beimportant?
In a horizontal pipe water flows at a rate of 9.1 L/s. Here, the pipe has two sections, one with a diameter of 10.16 cm and the other with a diameter of 5.08 cm, with a gradual smooth reducing section. In this case, a mercury manometer is used to measure the pressure difference. If friction is negligible how would I find the differential height of mercury between the two sections? If the manometer on the 5.08cm pipe section was replaced with a pitot tube how would the reading change? any help would be deeply appreciated
How does a siphon work? Are there any limitations (suchas how high or how low can you siphon water away from atank)? Also, how far—could you use a fl exible tube tosiphon water from a tank to a point 100 ft away?
A Pitot tube in a pipe in which air is flowing is connected to a manometer containing water asshown below. If the difference in water levels in the manometer is 10 cm, what is the velocity of flow in the pipe? Assume a tube coefficient of Cp = 0.99, specific weight of air is 12 N/ sq.m.
Find the pressure head at entry of the pipe, when the pressure of flowing fluid is 275 N/cm? The pressure head at entry (Unit in Pascal)?
In Fig. P3.130 the fl uid is gasoline at 20 ° C at a weight fl owof 120 N/s. Assuming no losses, estimate the gage pressureat section 1.
A pump discharges 8000 liters per minute of a certain brine solution (SG=1.20) to an evaporating pond. The intake line is 25cm in diameter and is at the same level as the pump discharge line, which is 15cm in diameter. The pressure at the inlet of the pump is -170mm of mercury. The pressure gage connected to the pipe discharge reads 150 kPa, and its center is 2.0mabove the center of the discharge flange. The vapor pressure of the brine solution is 40mm of Hg. If the pump efficiency is 80%. How much power is required?
[Mechanical] A 10cmm diameter external cylindrical mouth peice discharge under head of 4m .determine pressure at discharge and pressure at venocontracta. Cc=0.60 and atmospheric pressure=10.3m of water.
A ventury meter used to measure the liquid from the reservoir. The cross-sectional area at the inlet and throat are 4.536 x 10-3 m? and 1.134 x 103 m? with the flowrate of water is 9167 cm¾s. The level difference of mercury in manometer u tube shows the reading of 266 mm. Determine the flowrate coefficient. Given the specific gravity of mercury 13.6.
The inlet and throat diameters of a horizontal venturimeter are 30 cm and 10cm respectively. The liquid flowing through the venturimeter is water. The Pressure intensity at inlet is 13.734N/cm² while the vacuum pressure head at the throat is 37cm of mercury. Find the rate of flow. Assume that 4% of the differential head is lost between the inlet and throat. Find also the value of Cdfor the venturimete
An 11.5-in-diameter centrifugal pump, running at1750 r/min, delivers 850 gal/min and a head of 105 ftat best efficiency (82 percent). (a) Can this pump operateefficiently when delivering water at 20°C through200 m of 10- cm-diameter smooth pipe? Neglect minorlosses. (b) If your answer to (a) is negative, can thespeed n be changed to operate efficiently? (c) If youranswer to (b) is also negative, can the impeller diameterbe changed to operate efficiently and still run at1750 rev/min?