Q2) Two loads connected in parallel are respectively 2Kw at a p.f. of 0.75 leading and 4Kw at a p.f. of 0.95 lagging calculate the p.f. of the two loads and find the value of parallel element needed to correct the power factor to unity p.f. Assume that the load is supplied by 110V(rms), 60HZ line.

Q2) Two loads connected in parallel are respectively 2Kw at a p.f. of 0.75 leading and 4Kw at a p.f. of 0.95 lagging calculate the p.f. of the two loads and find the value of parallel element needed to correct the power factor to unity p.f. Assume that the load is supplied by 110V(rms), 60HZ line.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Related questions

Q: I- Purely Inductive Load 1. Sketch a three-phase 100VAC RMS phase-voltage, Wye (Y) Connected power…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: of the series connection of the resistor R0 and the inductance L0 between the terminals a and b.…

A: In this question we will find average power delivered to load..

Q: 9. The two loads in the circuit depicted below absorb the following power. Load, absorbs S = 6+j10…

Q: Q1//A power plant has to meet the following load demand: Load A: 100 MW from 8 AM - 6 PM Load B: 150…

Q: Consider the circuit shown in the Figure. a) Calculate values for IR. IL, Ic, VR, VL, and Vc. b)…

A: The given circuit is as follows Impedances j50 Ω and -j40 Ω in parallel and their equivalent is in…

Q: Suppose the circuit shown represents a residential distribution circuit in which the impedances of…

Q: Determine the complex power for the following give values and specify whether the power factor is…

Q: A generating station has a connected load of 43,000 kW and a maximum demand of 20,000 kW, the units…

Q: Problem 4: For the circuit shown in figure, compute the average power delivered to the load, the…

Q: The rms value of a three-phase balanced ac voltage source is 173V. Such voltage source is used to…

A: Given RMS value of three phase balanced ac voltage =173V Assuming line to line voltage⇒…

Q: Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase…

A: 1Real power P3ϕ is a cosine function of the total power and is given by,3 VLLILcosϕSo, it matches…

Q: A power station with capacity of 800 kW is to supply two loads (A & B). The daily load rve of the…

A: A power station, often known as a power plant, is a facility that generates electricity. A generator…

Q: A certain generating plant in manila has 40kV, three phase transmission line to supply a 12MVA load…

Q: Two interconnected substations O and P are interconnected via a distribution line of impedance 6 +…

Q: A single phase a.c. distributor AB is fed from point A has a total impedance of (0.1+j0.2) N. At far…

A: Given system is : Step 1: Calculate respective impedance Total impedance =0.1+j0.2 ΩiImpedance of…

Q: Two balanced loads are connected to a 240-kV rms 50-Hz line. Load 1 draws 30 kW at a power factor of…

A: Ans: a) Complex Power = 123.8 angle(43.86). Real power= 90 kw. Reactive Power = 85 kvar. b) Line…

Q: 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm…

Q: The

Q: 7. A power station has to meet the following load demand 50 KW 30 kW 20 kW between 10 A.M. and 6PM.…

A: Load A 50KW 10AM to 6PM Load B 30KW 6PM to 10PM Load C 20KW 4PM to 10AM Draw load curve, diversity…

Q: 5. The maximum load on the Thermal Plant of 60MW capacity is 50MW at an Annual Load Factor of 50%.…

A: Thermal power plant is generate the electricity . it is also known as a combustion power plant . it…

Q: or the following SLD, take SB = 100 MVA and VB = 250 kV at the load bus to he impedance diagram.…

A: In the question we have given all the per unit values on their respective bases. But since base…

Q: Two impedances Z 1 and Z 2 , when connected separately across a 230 volt, 50 Hz supply consumed 100…

A: Two impedances Z 1 and Z 2 , Voltage 230 volt, 50 Hz supply consumed 100 watts and 60 watts at power…

Q: Between the terminals a and b in the figure, there is a load formed by connecting the resistor R0…

Q: A 3500 ?? load with a power factor of 0.70 leading is fed from a source at 50 ?? with an RMS voltage…

A: Here, we have given the Apparent power, S=3500 VA Power factor, p.f.=0.70 leading so,…

Q: Exercise#4: A balanced wye-connected three-phase source has line-to-neutral voltages of 440 V rms.…

Q: the circuit in the figure, there is a load consisting of the series connection of the resistor R0…

A: In this question , we will find load value for maximum power deliver to load and maximum power…

Q: 1.3. The annual load of a substation is given in the following table. During each month, the power…

A: Below are the codes required to generate the load curve using barcycle function.

Q: Q4 Calculate the three-phase voltage drop if the ac resistance is 3 Q/2km and an ac reactance of…

A: In the Star Connection, the 3 winding's similar endpoints are connected to a common point known as…

Q: Example 1: Calculate the percent voltage regulation for a three-phase wye-connected 2500 kVA 6600-V…

Q: Referring to the Figure 1 below, set the value of voltage Vs as: - Vs (rms) = (120+the last 2 digit…

Q: R. Yük

A: a) we need to find our L0 and R0

Q: Two impedances Z 1 and Z 2 , when connected separately across a 230 volt, 50

Q: A generating station distributes the following loads. 2500KW, 7500KW, 15000KW and 3500KW, The…

Q: A generating station has a maximum demand of 55MW, a load factor of 63 %, a plant capacity factor of…

A: In this question load factor , use factor, capacity factor ,maximum demand given....We have to find…

Q: A power station has to meet the following load demand: LOAD A 50kW Between 10 AM and 6 PM LOAD B…

A: The solution can be achieved as follows.

Q: The daily demands of three consumers are given below in KW: Plot the load curve and find (1) maximum…

A: The solution can be achieved as follows.

Q: Determine: a. The network power factor b. The network phase angle c. The network impedance d.…

Q: A balanced A-connected load consisting of a pure resistances of 152 per phase is in parallel with a…

A: Explanation: a) Converting the delta circuit into an equivalent star circuit, so the per branch…

Q: Q.NO.4 Draw the load duration curve from given daily load cycle. Also find load factor, average load…

Q: 2.42 A balanced A-connected impedance load with (12 + j9) N per phase is supplied by a balanced…

A: In this question, Delta balance supply is supplied to the balance Delta load. Impedance of the…

Q: Assume that two load impedances Z, and Z, are connected in series with respect to each other but Z,…

Q: A generating station having two thermal generating units shown below with minimum an maximum…

A: In a power generation station, electrical power is generated according to the demand of the…

Q: T2 Vs R Vo AA chopper circuit in the figure, 400 V (rms) Control the power of an ohmic load from a…

A: Explanation: “Since you have posted a question with multiple sub-parts, we will solve the first…

Q: A generating station has a maximum 3 demand of 25MW, a load factor of 70%, a plant capacity factor…

Q: A power station has to meet the following load demand : Load A 50 kW between 10 A.M. and 6 P.M. Load…

A: Given: Load A 50 kW between 10 A.M. and 6 P.M Load B 30 kW between 6 P.M. and 10 P.M. Load C 20 kW…

Q: Q1//A power plant has to meet the following load demand: Load A: 100 MW from 8 AM - 6 PM Load B: 150…

Q: Two impedances are supplied by Vrms, as shown in Figure 2, where Arms. The first load draws P₁ =…

A: It is given that: P1=23.2 WQ1=50 VARAssuming,V=100∠160° VI=2∠190° A

Q: The annual load of a substation is given in the following table. During each month, the power is…

A: Below are the codes required to generate the load curve using barcycle function. Above is the…

Q: A 60-Hz, single-phase power line and a telephone line are parallel to each other as shown in the…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

Q2) Two loads connected in parallel are respectively 2Kw at a p.f. of 0.75
leading and 4Kw at a p.f. of 0.95 lagging calculate the p.f. of the two loads
and find the value of parallel element needed to correct the power factor to
unity p.f. Assume that the load is supplied by 110V(rms), 60HZ line.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
a short three phase transmission line connected to 33kv 50 hertz generating station at starting and is required to supply a load of 10 MW at pointed start lagging power factor at 30 KV addresses in that is the minimum transmission efficiency is to be determined96% estimate the per face value of resistance and inductance of a line
In the figure, the circuit is given as VRS =√3 . 60V and Zy = 6 + j8. Find the value of C to be connected in order to make the power drawn from the system in a phase 1, to make the load current 1, and to make cos(φ) 1.
Two balanced loads are connected to a 240-kV rms 50-Hz line. Load 1 draws 30 kW at a power factor of 0.6 lagging, while load 2 draws 45 kVAr at a power factor of 0.8 lagging. Assuming the RYB sequence, determine: (a) the complex, real, and reactive powers absorbed by the combined load, (b) the line currents, and (c) the kVAr rating of the three capacitors ∆-connected in parallel with the load that will raise the power factor to 0.9 lagging and the capacitance of each capacitor. Verify the results by creating a MATLAB Simulink model and program. Obtain the plots for the currents and voltages
Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase source to the 3-phase load. Match the following expressions, those on the left to those on the right. 0) Real power, Py (ii) Reactive power, Qu (ii) Total apparent power Sy (iv) Complex power, Sy (a) (V3 VLL. IL)VA (b) (V3 Vu sng) var (e) (V3 VLL. IL cos ø) W (d) Py +Qy Note that VLL is the rms line-to-line voltage, IL is the ms line current, and o is the power-factor angle.
A 480V single phase load has resistance of 70 ohms and inductive reactance of -j45 ohms. Find the real power, the apparent power, and the power factor consumed by the load.
Using a test equipment, Vmax was found to be 5V while Vmin is 1V. The distance between voltage maximas is 14 cm and the first maximum was found to be 7 cm from the load. What is the load impedance if the characteristic impedance of the line is 75 ohms?
Two interconnected substations O and P are interconnected via a distribution line of impedance6 + ?8Ω. Assume a load of 20MVA, at 0.8 power factor lagging is delivered at a bus-bar voltageof 66kV at P from O. Determine:a. the bus-bar voltage at substation Ob. the efficiency of distributionc. the power factor angle at O
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
A balanced 3-phase Y-connected source has using positive phase sequence, ?an = 390∠30˚ ?. Find the complex expression of voltage Eab. Circuits Problem 1